AutoCad :: Assemble Dynamic Blocks

Dec 12, 2013

I need to use lots of individual blocks as one big block. The blocks are dynamic and I'm looking for a way they can act like one

View 6 Replies


ADVERTISEMENT

AutoCAD Dynamic Blocks :: Annotative Parameters Inside Dynamic Blocks

May 5, 2010

I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.

In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.

The attached file shows a simple example.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Adding One Action To Dynamic Blocks

Mar 15, 2012

I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.

This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g.  I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).

I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.

I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.

View 7 Replies View Related

AutoCAD Dynamic Blocks :: Insertion Point On Dynamic Blocks

Apr 23, 2013

I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.

My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Stretching Dynamic Blocks

Sep 7, 2012

is there a way to make dynamic blocks stretchable similar to a mleader,

the blocks i create are only stretchable by grips, and not by crossing

(i am using linear or point parameter stretches)

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Grips And Dynamic Blocks

Jun 1, 2006

Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.

View 4 Replies View Related

AutoCAD Dynamic Blocks :: Link Dynamic Block Custom Rotation Action

Mar 22, 2013

So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it.  However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle.  Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.

This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Moving Properties Table Grip In Dynamic Block

Jun 13, 2013

I have a dynamic block, that represents a stirrup.

I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.

The problem is that I can't make this grip moveable )

See the attachement with the block

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Flipping Dynamic Block With Multiple Items Not Visible

Jul 25, 2012

new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way.  I now want to add an overall flip to the entire block and have not been able to find set this.  I would prefer to use the same label and go from there.  I have included the block to show what I mean.  It is only working on the single visible item at the one time.  I know this has to be possible just let me know what I am doing wrong.  I am running AutoCad LT 2013 

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Create A Dynamic Block For Glass Panel In Balustrade

Feb 28, 2012

I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.

I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right  hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Insertion Point Of Attribute Changing Within Dynamic Block

Nov 21, 2011

I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.

But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Pass Attribute Values To Dynamic Block Parameters?

Dec 4, 2013

I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.

View 1 Replies View Related

AutoCAD Dynamic Blocks :: How To Disable The Dialog Box Shown When Open A Dynamic Block

Nov 7, 2011

I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.

Is there a way to disable that dialog and open the files as normal dwgs?

A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...

View 4 Replies View Related

AutoCAD Dynamic Blocks :: Printing Dynamic Titleblocks With Visibility States

Feb 15, 2012

usage of dynamic title blocks with visiblity states and defining page setup override templates which use same for quick plotting using sheet sets.

I have attached a simple dynamic block that I built which is the outter frame of our company title block, it is designed to allow users to quickly switch between Landscape and Portrait orientations. 

The problem I am having is when I go to define page setups for my Sheet Set Page Setup Override Template I am unable to use the "Extents" option with auto-center because the "Extents", as defined by the page setup, includes ALL objects in the paper space regardless of visibility, so my title block ends up being centered in a stupid way if that printing configuration is used. 

The only solution I have found is to use the "Layout" option when defining page setups, but this option produces other issues in other ways when printing.  I don't want to use the "Window" option either for the potential for users to be using the page setup overrides to print drawings using different paper sizes or drawings that were not originally created using the current template the override is designed to accomodate.

Is there perhaps a system variable that defines whether invisible objects are included in the "Extents" setting in the page setup?  I'm sure you'll all agree that Extents is the way to go in this situation, but it is not performing exactly as required.

View 5 Replies View Related

AutoCAD Dynamic Blocks :: Make Dynamic Block Of Column Radiator

Mar 26, 2012

I'm trying to make a dynamic block of a column radiator.

It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).

My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.

View 4 Replies View Related

AutoCad :: Insert Dynamic Block From File With Multiple Dynamic Blocks

Jul 16, 2010

I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".

For that i tried creating a new command "INSERT_M12" that has the following script :

^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"

Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Join Two Dynamic Block To One Common Action?

Sep 18, 2013

I'm working on a drawing and I want an action to work on two diffrent dynamic blocks. 

In my case, I wish to have two blocks that I can rotate by one rotation grip.

How do I manage to work this out?

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Stretch Dynamic Block Grip Points

Feb 4, 2011

I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.

I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.

But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Variable To Change Dynamic Grip Parameter Size And Color

Oct 11, 2012

What is the variable to change the dynamic grip parameter size and color.

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Dynamic Door / Specific Parameters To Change Its Size And Orientation

Dec 13, 2013

I'm working on a dynamic door, that has specific parameters to change its size and orientation. Everything works pretty good, only the arc for the door won't react the way I want it.

View 8 Replies View Related

AutoCAD Dynamic Blocks :: How To Create WAVE Dynamic Block

Mar 1, 2013

I would like to create a "wave" dynamic block, see below...

It is made from wipeout.

Is it chance to make a similar?

If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Scaling Objects In Dynamic Block

Jun 27, 2013

Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.

I tried adding position point and link, etc....I run out options and don't know how to fix this.

LT 2012 user

AutoCAD LT 2012
Windows 7 - 64 bit

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Grip Point Dynamic Block

Nov 15, 2012

I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).

View 9 Replies View Related

AutoCAD Dynamic Blocks :: How To Keep An Object Centered On A Dynamic Block

May 29, 2013

I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered

I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.

View 6 Replies View Related

AutoCAD Dynamic Blocks :: Dynamic Stretch Grip Gets Offset

Apr 4, 2012

Is there a way to have the grip stay in the correct position when the distance multiplier is .5? It seems to "get ahead" of the original location.

In the attached block, when I stretch the block with the grip, the grip ends up off the end point.  Both actions have a .5 multiplier, with the left side having a rotation of 180 - so both sides stretch equally in opposite directions.

Also, there are 3 views with parameters (width/depth). Is there a way to get the user to enter in the sizes without having to select the size on each view? Basically a table that has a 'user input' field so the size selected changes everything at one time.

View 7 Replies View Related

AutoCAD Dynamic Blocks :: Create Dynamic Block With Dimension

Jan 4, 2014

I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.

LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi

Then, I use command DAL; I can select dimension want use.

View 8 Replies View Related

AutoCAD Dynamic Blocks :: Stretch A Hatch In Dynamic Block?

Jul 4, 2013

How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Keep Item Centered In Dynamic Block?

Mar 5, 2012

I have an X centered as my insertion point.

When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.

how to get the X to be centered in the box when it is enlarged to a double or triple size?

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Mirrored Rotation Dynamic Block

Jun 14, 2012

Is it possible to mirror a rotation within a dynamic block?

See the attached drawing.  I am trying to have two rotations within a dynamic block, but only one grip.  When the grip is rotated one half of the block rotates while the other half rotates in reverse.  The resulting action would be much like the wings of a butterfly.

I have tried many different combinations of parameters, actions and constraints with no luck.  The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?

View 7 Replies View Related

AutoCAD Dynamic Blocks :: Dynamic Block Linear Array?

May 5, 2012

I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.

View 5 Replies View Related

AutoCAD Dynamic Blocks :: Selecting A Edited Dynamic Block?

Mar 28, 2011

I have the attached file as a dynamic block.

Last week I opened the drawing and added some visibilty states etc. to the block.

Now when I open the block or insert it into another drawing for whatever reason the cursor or crosshairs stop at the edge of the block. And if you move towards the middle of the block where there isn't any lines etc. the cursor will move to that point until you hit another line then it will stop moving again.

I've been reading some other posts for different dynamic block topics/issues and read that everyone has problems when you get to higher numbers of visibility states, but when I edited last week I only added 7 states. Is that enough to make this happen? It sounds like everyone else that is having problems has far fewer visibility states than on the attached drawing. 

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved