this is my first query how to calculate man hours per drawing. whether based on size(a1,a2,a3,a4) , or by based on drawing.. some companies they are calculating based on sheet size...
View 9 RepliesI am trying to find out a good way to calculate hours minutes seconds , know a good program I can use on my phone. I am trying to add
35:42:16+17:53:57
I'm trying to work out a way to calculate the fill volume difference for a proposed landscaping plan (images attached) and how to model and calculate the amount of fill required to do the job.
Site-Plans-4-Recovered.jpgSite-Plans-4-Recovered2.jpg
I´m triyng to do a autolisp routine to calculate the perimeter of a drawing with several entities like arc, polyline, spline, lines and circles.
In the web i found out a autolisp routine that calculate this but it doesnt recognizes circles.
I need that the circles can be recognized, does some one knows how i can do that?
Mac Pro
2x2.8 Quad Core Xeon
10 g 800mhz mem
ATI 5770
PS CS5 12.04
Working on image @ 3010x5562 240ppi 22M
After working for a few hours, using various brush, including Mixer Brushes, I started to get brush lag and this just got worse as I went on!I tried clearing cache, saving and rebooting, but still have problem!I have also tried opening another image, but had the same problem, so I can only assume this is not a image problem as such, but a resources fault with Photoshop?!
PSE 10 Elements Organizer in "Building index ..." has stayed at 73% for 17 hours. Is it frozen? Is it time to cancel and re-start indexing? Reason for asking, when tried to convert PSE 8 to 10 in April, Adobe did not state that the freeze at 34% was "normal". Have since then not been able to do a backup and had to manually move 4000+ photos from various files (resulting from the multiple conversion attempts) into the appropriate file to reconnect and just completed that task yesterday. All files were reconnected; the catalog was repaired even though did not need to be and now the indexing problem. It's been a long 6 months of struggle.
View 3 Replies View RelatedCan I burn a file that is 3.5 hours long on to one dvd. Also, I do not see the MPEG 1 option in Premier Pro CS6.
View 4 Replies View RelatedIn PSE12 importing photos from the new Leica M (mod 240) are lost when importing the hours and minutes of shooting single frames, which are replaced with those of day and time of import.
View 1 Replies View RelatedVideo files from an iPhone 4S (5.1.1) are transferred onto my Mac (this story is true under 10.7.4 and under 10.8) via PhotoSync. In Finder, the files reflect the correct creation date. On importing the files to Aperture, the correct capture time and date is shown in the metadata. On importing the files to Lightroom 4.1, however, the capture time shows as plus-five hours from when actually shot. I can't think of any setting I might have tripped in Lr to cause this to happen on import (I understand how to manually change the capture time).
View 17 Replies View Relatedi created new polygon´s SDF (ACAD Civil,Map2011). And created new feature from geometry (from 2 closed plines - island). See on attached picture. If polygons are more complex =erroneous result from calculation ("Round ( Area2D ( Geometrie ), 0 ) "). It means ACAD calculate sum 2 areas together, but It should dedust island from main polygon.
View 3 Replies View Relatedcalculate the volume.I attached here my dwg file. I never done this before and I want to know the correct answer when I want my land to be levelled at 6m.How much volume to fill and the land to be removed.
View 9 Replies View RelatedHow to Calcuate the area of a layer, through .NET API ?
View 9 Replies View RelatedI'm using AutoCAD 2013 x64 and VS2012 Express with ObjectARX 2013. Now I want to calculate the (projected) intersection point of 2 (intersecting) lines in vb.net
After selecting the lines I have this line1.IntersectWith(line2, Intersect.OnBothOperands, intpts, 0, 0)
In Visual studio express 2012 I get the following warning for the above line of
warning BC40000: 'Public Sub IntersectWith(entityPointer As Autodesk.AutoCAD.DatabaseServices.Entity, intersectType As Autodesk.AutoCAD.DatabaseServices.Intersect, points As Autodesk.AutoCAD.Geometry.Point3dCollection, thisGraphicSystemMarker As Long, otherGraphicSystemMarker As Long)' is obsolete: 'Use the overload taking IntPtr instead.'.
So, if I'm reading this correctly, this method is outdated and I should use an other method to calculate the intersection. But I really don't know what 'Use the overload taking IntPtr instead' means.
One of the things I found is a function that contains this line of Dim inters As Point3d = line1.IntersectWith(line2)(0). This one looks almost the same, but doesn't give me the warning when I compile the code, but this method crashes AutoCAD when there is no intersection between the lines. This is despite a try catch block that surrounds the code.
For now I just want to use lines, but I need to expand the code so it will also work with circles, arcs and polylines.
I draw something one the drawing fisrt,
then open one windows form。
The problem is the form location。I do not want the form cover the graphic what i was drawing before.
Maybe, there is a way to Caculate the Point of the screen by Entity
There are points in different levels i wanna make the surfer with this points and project the surfer on the down surfer(that makes with other points) after that make an enclosed Volume and finally Calculate the Volume between this 2 surfer. How its possible to Calculate?
View 8 Replies View RelatedI have a question: ¿Which scientific calculation's method usually autocad utilize to calculate areas?
View 1 Replies View RelatedIf I want to calculate the square mm of an area, how do I do so? I know this should be really simple but I can't get the results I want. Let's say I have a rectangle (2D) and I draw somew circles and polylines within it that are 'cut out' from the rectangle....how does one calcualte the remaining square mm?
View 9 Replies View RelatedHow to calculate in AutoCAD the Conversion factor. I need to calculate the complete Building Floor and I try the field command in AutoCAD, But I don't know what I should write to conversion factor.
View 9 Replies View RelatedI need to calculate the areas within a set of lines that form a closed area.
1. How do I do that?
2. Do I need to create a polyline around the area, or is lines enough?
I use AutoCad Map 2000i
If I want to draw a 10% slope on 5' contours how do I calculate the circle diameter needed to construct the slope in order to connect the lines where the circles intersect the contour?
View 1 Replies View RelatedIs there a way to calculate a (closed) 3D polyline area ?
View 8 Replies View RelatedI am trying to calculate muck away for work, and I have drawn the site plan in millimetres for accuracy. However when I try to calculate the volume I get this value: 3.6293E+12. I am guessing that it is saying this due to the fact its in millimetres, and I am trying to calculate a large area and convert in into metres squared. What this value means?
View 1 Replies View RelatedI'm struggling with the maths needed to calculate the angle between 3 points. My eventual aim is to use vba to draw a crescent shape polyline, ie 2 arcs curving in the same direction and joiing at their tips. Both arcs will have different centrepoints but the same radius. The only info I know so far is radius (R), centrepoints (CP1, CP2) and the intersection points where their end points meet (IP1, IP2). I've gotten those points by using the 'IntersectWith' function on two circles.
My coding skills are fine it's just the maths I'm struggling with and after searching google for quite some time I'm still confused. I've looked at loads of differnet formulaes and diagrams, but it always seems like they aren't complete. Maybe it's just me.
I don't know about open traverse...how to do open traverse and how to adjust it.
View 3 Replies View RelatedHow do you get the spacing you want for a hatch? For example if using ANSI 31if under pattern scale you have 1.0 what spacing does 1.0 represent? If you want your lines 1'-0" apart how to you know what scale to use other than trail and error?
View 1 Replies View RelatedWhat formula Civil3D uses to calculate the average slope of a surface?
The formula I am using is S = I*L/A
S = Average Slope
I = Contour Invertval
L = Length of Contours (ft)
A = Area of parcel (sq. ft)
I just had to do four parcel calcs and the percentage I find using the formula is always 1-3% lower than the percentage Civil3D spits out. I can't find anything about how Civil3D arrives at that number, it just appears. I assume that Civil3D is more accurate but I can't give that number to a client without knowing how the program arrived there.
How do you calculate paint area?
We do a lot of chutes (for mining). They need to be painted on the outside only. They also need to be lined with rubber sheet on the inside. The area given in the physical tab in iProperties is the total area.
The area of the edges of the plates are small enough that we can ignore them, but is there a way to calculate half the model's area and get that result in the drawing in a text note?
We've only recently switched over to Inventor (used to be on Solidworks, where we had the same problem).
I need to calculate square footage quickly. I am currently polylining everything. Here is what I need to do quicker:
Calculate square feet of each room with these requirements:
- When meeting a hallway to the outside face of the wall
- when next to an adjoining space, to the midpoint of the wall
- When against an outer wall, going to the face of the wall.
I have a cast aluminum part I need to calculate the surface area for our plating process. I have done a simple area, its not right (.015ft^2). I have derived it as a surface but can't get a volume calculation.
View 9 Replies View RelatedTrying to calculate a catchment area to allow me to size some culverts using Civil 3D 2012 Sp#1.
" The specified location results in a Catchment with no area."
After sitting for 15 miutes I keep getting the above message. The surface is huge and there is an obvious catchment area (or I think it is obvious). The surface was generated from contours and cover an area of approx. 8Km x6.5Km but the catchment ares should be around 15-20% of that area.
I tried another one upstream about a Km and it worked fine. So the one I am doing now should encompass the upstream area as well as from that point downstream to the Discharge Point.
I am designing wing ribs for a prototype, ribs made with fir wood; I must make cuts in the ribs in the form of circles or triangles to reduce the weight but keep the strength. I think I will use circles because a triangle's corners can be starting points for fissures(maybe triangles with rounded corners?).
Given: wood type,fiber alignment, rib dimensions, pattern of circles and circles' diameters, can Autocad calculate the forces that rib can withstand on each axis ox,oy,oz?
Is there another program that can tell me what forces an object can withstand given information about that object?