I have created a circle from 3topo points. Im having difficulty getting accurate elevation (z) of the center of circle (pile representation) via cad polyline listing. im getting same "z" all through out which in fact is not.
View 8 Replies
Is there anyway to use LISP to list the x,y coordinates of a pline?
View 3 Replies View RelatedI am looking for a method to export all the GPS coordinates which have been assigned to each point along with the properties of that point to an excel csv. In our drawings, there are multiple columns and each column has four points and each point has X,Y,Z coordinates. I want to export all this information to an excel sheet.
View 3 Replies View RelatedI want to get the minimum and maximum x, y coordinate values of selected lines. In other words, i want to find the top, bottom, left and right edges of a set of lines.
Is it possible to achieve this with a lisp code?
I need to draw a table with point number, easting, northing, elevation for a lot of points and need a lisp to read the xl spreadsheet and draw the table.
View 9 Replies View RelatedI'm writing function which will facilitate user to offset dimension. After enter command, he select dimension and select point near one of dimension's arrowheads. Then I'm calculating new XLinePoint1 or XLinePoint2 and replacing original.
I have everything done. I thought ... The problem is when user firstly create AlignedDimension and after that he create RotatedDimension by using continous function. After that XLinePoint1 and XLinePoint2 are not parallel to the DimLinePoint (look at image).
How can I get coordinates of points selected in red rectangles?
I know that one is specified as "dimension line defining point" but what about second? How can I get its coordinates? Or maybe there is other way to get this point?
I recently wrote a lisp routine that was supposed to get the 4 coordinates of a rectangle (LWPolyline). It worked fine in *MY* tests. But when someone else ran it, the routine operated as though the order of the points had been rearranged.
How can I get the points AND the order in which they belong?
Here's a sketch to show you what I mean. As part of my troubleshooting, I had a lisp routine draw a new pline using the points gathered by my first routine. The result of that on the left. On the right is the result of that when someone else runs the two routines.
Here's the code I used to get the points.
(defun getplinepointlist(ename)
(setq ent(entget ename))
(setq ptlist (list))
(while (setq pt(cdr(assoc 10 ent)))
[code].......
I am having nearly 1000 drawings where I need to change the title block in a new format.
I am stuck up in moving all the entities in cordinates 15,280 (upper point) and 205,55 (lower Point) to 275,294 (upper point and correspoing lower point.
Is it possible to obtain a list of coordinates for view ports (with dxf codes or otherwise) similar to obtaining a list of (assoc 10) for polylines?
I'm aware I can get the center, width and height from the dxf codes, but what about for clipped view ports with irregular shapes?
i have found the following lisp in a previous thread: (shows XY coordinates of the selected blocks)
(defun C:MyFunc (/ ss Index Ename Lst)
(while (or (not ss) (= 0 (sslength ss))) (setq ss (ssget '((0 .
"INSERT")))))
(if ss
[Code]....
I want this information to be added to the blocks as hidden attributes so that i can extract them by attout. The work to be done is : attout to excel, autofill an attribute (numbering) then attin.
but my problem is that i cant think of a way to number those blocks IN ORDER (ie top to bottom or left to right) unless by sorting them in excel first by their x or y coordinates
can do a routine that zooms into a coordinate, based on input. So for 1A, it would zoom into the coordinate for 1A.
1A = 1,1
1B = 1,2
1C = 1,3
1D = 1,4
I will try to attempt one shortly and will post it within 1 hour.
I have a 2 point LWPOLYLINE that has the following coordinates at its end point when I 'ID' the point.
Command: id
Specify point: end
of X = 709369.3214 Y = 7153039.9690 Z = 269.2143
However if I use..
(vlax-safearray->list (vlax-variant-value (vla-get-coordinates (vlax-ename->vla-object (car (entsel))))))
I get this
(-450567.0 269.288 -450570.0 269.214)
and if I 'dump' the object..
; Coordinates = (-450567.0 269.288 -450570.0 269.214)
; Document (RO) = #<VLA-OBJECT IAcadDocument 09855674>
; Elevation = 7.17399e+006
I don't have a clue where the '-450567.0' is coming from.
I'm in Model Space in 'World' UCS, and I'm confused.. why does the 'ID'd' value not reflect whats going on when I use the vla-get-coordinates approach.
There are many other LWPolylines within the same model that behave normally.
I've attached the drawing (I think!)
I have few co-ordinates in notepad like mentioned below. How can i create polyline using read-line function in auto lisp.
x y
0.0,0.0
2.0,0.0
2.0,1.0
0.0,1.0
2.0,0.0
4.0,0.0
4.0,1.0
2.0,1.0
I’m trying to create a view port, which covers my entire layout (white/ page area) using the following command
(command “mview” ‘(0 0 0) ‘(297.5 210 0))
However as you will note 0,0,0 is not the very edge corner of my layout (white area) and my white area is smaller then 297.5x 210mm (standard A4 landscape size)
How to obtain the exact measurements and starting coordinates to fully fill my entire layout page (white area)?
We have several AutoCAD drawings with hundreds of block references inserted with imprecise coordinates. Now we need to dimension all elements and need to correct these positions.
I am searching for a routine to round these positions up or down towards a 5mm precision so I don't have to manually move every single block element.
Is there any way to automate the task or do you know any workaround (like inserting the elements into a drawing with poorer unit precision settings)?
Would like to be able to select mtext explode it get x y coords of last line of text then turn it back to mtext and then launch mtext at a @0,-0.5 justification TL width 5 and display the ribbon.
All seems to work except the (command ...)
Below is my attempt.
(prompt "Select Note")
(setq ss (ssget))
(command "explode" ss)
(setq ss (ssget "l")) ;get last line of text
(setq ent (entget (ssname ss 0))
ent1 (cdr (assoc 10 ent))) ;get x y coords
(command "undo" "1") ;set exploded mtext back to mtext
(setvar "lastpoint" ent1)
(command "mtext" "@0,-0.4" "j" "TL" "w" "5")
I found this LISP code that can insert a block at coordinates from an ASCII.
(defun c:universal( / file f a osmode);PointsToBlocks(while (not file)(setq file (getfiled "Input file" "coords" "txt" 4)))(setq f (open file "r")osmode (getvar "OSMODE"))(setvar "OSMODE" 0)(while (setq a (read-line f))(command "._insert" "block1" a 1 1 0))(setvar "OSMODE" osmode)(princ)
What I want to be able to do is insert blocks from an ASCII and also set the x-, y-, and z-scales.
For example, I have these lines in ASCII, the data points refer to X position, Y position, Z position, X scale, Y scale, and Z scale.
30.593589,21.274607,26.235255,0.172826,0.766324,0.066442
30.710182,21.379792,27.054248,0.130816,0.700035,0.043114
I am just starting learning lisp, And I am looking for a fast way to select multiple objects (usually circle) and export their coordinates and ID into a excel sheet through lisp programming.
As you might see in the attached drawing, the red circles are objects wanted. I have been trying to export their coordinates as well as their IDs in grids, e.g D28, Easting: Northing: . I still haven't found a good way to export ID for each circle.
As my code doesn't work, I wonder what's the most effective way to detect errors in lisp
I'm trying to define a grid based on polar coordinates.
Can be produced using the following MATLAB
n=1:50000;r=sqrt(n);t=360/((sqrt(5)+1)/2)+1)*pi/180*n;plot(r.*cos(t),r.*sin(t),'o')
I need to insert points based on the polar coordinates defined by the equations. I knew a little bit of LISP 10 Years ago, now it's a total blank. I've been trying to write a script to make this work but after 5 days I'm still without sucess.
I got a new work and get it done in the next 2 days, but first I need to do this... from a text file (or excel file, I got both) I got 3 columns, 1 one for node number, and 2 other for X and Y coordinates for each node.
So from that file I need to insert into autocad the node numbers as text (using the current style and height) at the point specified by the other two columns, that are the X,Y coordinates which will be the insertion point of text..
I have a rather simple 3rd party custom object... I tried to get its bounding box but the coordinates that come back don't seem to relate at all to the object.
What I'd like are the coordinates of two nodes the object contains...
Is it possible to apply the autocad cursor in some why with the node object snap to get their coordinates?
Is there a lisp that will allow me to do a continuous dimension, but will alternate the dimension position from low, high, low and high? If there is no lisp already created, how to create one?
See Continuous dimension attachment for example.
I work at a glass and glazing company and this is how we dimension mullion width and DLO. See typical window dimensioning attachment for window elevation with dimensions.
I have a list ("temp.dwg" "temp2.dwg") and would like to add the string "insert text here" into each item in the list resulting in ("insert text heretemp.dwg" "insert textheretemp2.dwg"). how would i go about doing that using LISP?
View 2 Replies View RelatedIs there a way to programatically set a visual style before a drawing actually opens?
We have some huge models and people seem to forget to change their visual styles back to 2D wireframe before saving and exiting drawings. Some models will crash on some workstations when trying to open in a rendered mode.
I found a lisp with a function that looked to set viewport visual styles. But it does not seem to be supported anymore. --> (vla-put-VisualStyle vport 1)
I'm trying to write a lisp routine that, when I invoke the mleader command, osmode is set to "nearest" & orthomode is set off. I then would like the original settings to be returned.
attached is what I have written so far:-
Lisp that switches back on Selection Preview i.e. thickens and highlights lines when you hover over them?I don't know why, but they are always unticking the boxes.
View 4 Replies View RelatedIs it possible to execute a certain command based on multiple selections withinin a dcl? for example: two radio colums, one with selections A and B, and a second with selections 1 and 2. is it possible to program commands based on user selections from each column? ex: if A and 1- do a command. A 2- do a different command, etc...
I tried :
(action_tile "key1" "(setq A t")
(action_tile "key2" "(setq B t")
(action_tile "key3" "(setq 1 t)(done_dialog)")
(action_tile "key4" "(setq 2 t)(done_dialog)")
(if
(and (a) (1)
)
(command ...
but was unsuccessful. no matter which combination was selected, the command under all combinations would run.
I am trying to find a lisp that would get an attribute value (tag name = NBR_5) . I'm trying to run a simple routine that would let the user place the value from the titleblock attribute as text on a drawing. I see a ton of articles regarding getting attributes but I am not well versed in programming.
View 9 Replies View RelatedI have a routine that work fine, but I receive a nil at the end of command. How to fix that?
View 7 Replies View RelatedI'm trying to find acceptable point values to feed to the vlax-3d-point function for a vla-addmtext function. With vanilla lisp I just provide the point as x y = "7/32" "2-3/8". So I assumed that I could drop a 0 in for the z like: (VLAX-3D-POINT "7/32" "2-3/8" 0).
Then I thought I was going to be tricksy and try (vlax-3D-point (getpoint)) believing that I could pick the point and get what I need to feed the function, but yet again, no deal. The command line gave me:
node
of #<variant 8197 ...>
Nothing I can use in my code. So how do I find the point in a format that vlax-3d-point will like?
What is the magic word for put a point at each end of an arc, the lisp I have only put a point at center of the arc.
(defun cAA ( / i j ss e1 e2 p1 p2 p3 points )
(if (setq i -1 ss (ssget '((0 . "ARC"))))
(progn
[Code].....
