Brackets in alternate units ...?
Is there any possible way to eliminate the brackets from around Alternate Units? I could swear I've seen a routine around that enables you to do this.
Is there a lisp that will allow me to do a continuous dimension, but will alternate the dimension position from low, high, low and high? If there is no lisp already created, how to create one?
See Continuous dimension attachment for example.
I work at a glass and glazing company and this is how we dimension mullion width and DLO. See typical window dimensioning attachment for window elevation with dimensions.
Id like to append a file with the following text...
(load "C:/ICT/GEBERIT/LSP/GEBERIT.LSP")
Quotation marks and all but how do i Handel them and the open and closed brackets using the following lisp example
(setq f(open "C:/ICT/AutoCAD_Architecture_suite_2012/LSP/acaddoc.lsp" "A"))(write-line "(load "C:/ICT/GEBERIT/LSP/GEBERIT.LSP")" f)(close f)
Is there a way of opening existing cmds in the visual lisp editor and edit them to do something else? I'd like to set up a lisp where 'uu' would switch the drawing units from decimal to architectural units and hittng 'uu' again would switch it back.
View 4 Replies View RelatedI am trying to sort a list of lists by the size of units.
Here is the unsorted list -
(setq List_Blocks
(list
(list "10x10" "UNIT DOWN-CC" 56)
(list "7.5x10" "UNIT DOWN-CC" 20)
(list "5x5" "UNIT DOWN-CC" 34)
(list "10x15" "UNIT EXTERIOR" 32)
(list "5x10" "UNIT DOWN-CC" 31)
(list "10x20" "UNIT EXTERIOR" 24)
(list "10x30" "UNIT EXTERIOR" 13)
(list "10x25" "UNIT EXTERIOR" 2)
)
)
I would like the list sorted by the first number before the "X" and then by the second number after the "X".
Example of sorted list -
(list "5x5" "UNIT DOWN-CC" 34)
(list "5x10" "UNIT DOWN-CC" 31)
(list "7.5x10" "UNIT DOWN-CC" 20)
(list "10x10" "UNIT DOWN-CC" 56)
(list "10x15" "UNIT EXTERIOR" 32)
(list "10x20" "UNIT EXTERIOR" 24)
(list "10x25" "UNIT EXTERIOR" 2)
(list "10x30" "UNIT EXTERIOR" 13)
Using AutoCAD 2013, I have set my the placement of the alternate units to "Below primary value" (in Dimension Style), but they do not go underneath, they remain after the primary units. I tested in 2012, and it works fine there but not in 2013.
View 3 Replies View RelatedWhen using alternate dimensions in hole notes it repeats the full note for both dimension units. I would like to only have the dimensional data have the alternate information and not repeat the full note (see attached file).
IV 2010, Vista 64
I am using 2012 SP2 and when I try to place hole notes with both metric and inches it only gives me inches (in both displays)
View 4 Replies View RelatedIs it possible to indicate alternate units, imperial/metric?
View 3 Replies View RelatedI have a list ("temp.dwg" "temp2.dwg") and would like to add the string "insert text here" into each item in the list resulting in ("insert text heretemp.dwg" "insert textheretemp2.dwg"). how would i go about doing that using LISP?
View 2 Replies View RelatedIs there a way to programatically set a visual style before a drawing actually opens?
We have some huge models and people seem to forget to change their visual styles back to 2D wireframe before saving and exiting drawings. Some models will crash on some workstations when trying to open in a rendered mode.
I found a lisp with a function that looked to set viewport visual styles. But it does not seem to be supported anymore. --> (vla-put-VisualStyle vport 1)
I'm trying to write a lisp routine that, when I invoke the mleader command, osmode is set to "nearest" & orthomode is set off. I then would like the original settings to be returned.
attached is what I have written so far:-
Lisp that switches back on Selection Preview i.e. thickens and highlights lines when you hover over them?I don't know why, but they are always unticking the boxes.
View 4 Replies View RelatedIs it possible to execute a certain command based on multiple selections withinin a dcl? for example: two radio colums, one with selections A and B, and a second with selections 1 and 2. is it possible to program commands based on user selections from each column? ex: if A and 1- do a command. A 2- do a different command, etc...
I tried :
(action_tile "key1" "(setq A t")
(action_tile "key2" "(setq B t")
(action_tile "key3" "(setq 1 t)(done_dialog)")
(action_tile "key4" "(setq 2 t)(done_dialog)")
(if
(and (a) (1)
)
(command ...
but was unsuccessful. no matter which combination was selected, the command under all combinations would run.
I am trying to find a lisp that would get an attribute value (tag name = NBR_5) . I'm trying to run a simple routine that would let the user place the value from the titleblock attribute as text on a drawing. I see a ton of articles regarding getting attributes but I am not well versed in programming.
View 9 Replies View RelatedI have a routine that work fine, but I receive a nil at the end of command. How to fix that?
View 7 Replies View RelatedI'm trying to find acceptable point values to feed to the vlax-3d-point function for a vla-addmtext function. With vanilla lisp I just provide the point as x y = "7/32" "2-3/8". So I assumed that I could drop a 0 in for the z like: (VLAX-3D-POINT "7/32" "2-3/8" 0).
Then I thought I was going to be tricksy and try (vlax-3D-point (getpoint)) believing that I could pick the point and get what I need to feed the function, but yet again, no deal. The command line gave me:
node
of #<variant 8197 ...>
Nothing I can use in my code. So how do I find the point in a format that vlax-3d-point will like?
What is the magic word for put a point at each end of an arc, the lisp I have only put a point at center of the arc.
(defun cAA ( / i j ss e1 e2 p1 p2 p3 points )
(if (setq i -1 ss (ssget '((0 . "ARC"))))
(progn
[Code].....
Is there a quick way of getting the value of an attribute?
I have an attributed block called "tp_attributes" and it has and attribute called "OrderNum".
I just want to be able to quickly grab that value.
I use Spell Check regularly and I always check the entire drawing. I would like to add to the Spell macro so that when I pick Spell from the toolbar it goes past the Check Spelling window and begins checking the entire drawing.
I believe I need to insert Alt S into my macro to select Start from the window to begin the check. Is there a character or series of characters that will represent Alt in a macro?
I upgraded from Autocad 2004 to 2012 recently and my lisp file doesnt work anymore.
what it's supposed to do is when looking at the layout tab that you want you can switch to the model space location of the same zoom as the layout tab without messing with the layout zoom.
(defun c:msp ()
(setq cm (getvar "cmdecho"))
(setvar "cmdecho" 0)
(command"view" "d" "tmp")
(setvar "tilemode" 0)
(command"pspace")
(princ "Click TWICE on desired VPORT: ")
(command "mspace" pause "view" "s" "tmp")(princ)
(setvar "tilemode" 1)
(command "view" "r" "tmp")
(setvar"cmdecho" cm)
(princ)
)
I need a program that simulate this DOS command: dir /on/b *.dwg >list.txt
it list all dwg files on current open dwg file folder and sort them and finally put them in a text file with list.txt name. something like thistype list.txt)
test1.dwg
test2.dwg
test100.dwg
test256.dwg
test1005.dwg
(sort alphabetically and logically) because of disabled DOS utility in my PC I need a pure lisp functions, I tried to wrote this program but I couldn't!!
(defun c:listMaker()
(vl-load-com)
(setq path (getvar "dwgprefix"))
(setq fn "list.txt")
[code]...
and also I need a append a string(='This Is EOF') in the last line of the "list.txt" file.
I have text objects with the same Z value and I will select as follows:
(setq sstxt (ssget '((0 . "TEXT")(8 . "APS-text"))))
How to store this value in another variable "zvalue" to apply to:
(command "change" "select text objects" "" "_p" "_e" zvalue "") ?
the following returns true since the @ symbol tests for an alpha character.. (wcmatch "S101" "@*").What is the Dot Net equivalent?
View 2 Replies View RelatedIs there a command that is the opposite of starting an application to open up a file? Like:
(startapp "PlaySound.exe" (findfile "CuckooClock.wav"))
Instead of starting an application, how to shut all of its instances down. Let’s say I have iTunes and/or Internet Explorer w/ a few tabs open and I can close them down without getting to the application to terminate it the usual way.
Naturally,
(endapp "iTunes.exe") doesn’t work :-))
I am trying to get my original layer and lintype reinstated after the user is finished with the pline..I know Im suppose to use the while command but am now completely lost on which way to do this
(DEFUN c:TEST1 ()(if (not (tblsearch "LTYPE" "MYWC")) (command "-linetype" "LOAD" "MYWC" "C:/COUNTER.LIN" ""));SECOND PROGRAM...;CREATE CORESPONDING LAYER...(command "._Layer" "Make" "WC LEIDING" "Ltype" "Continuous" "" "Color" "211" "" "")(SETQ MYOLDCELTYPE (GETVAR "CELTYPE"))(SETVAR "CELTYPE" "MYWC")(while (PROGN(COMMAND "pline")(SETVAR "CELTYPE" MYOLDCELTYPE)))
I have a drawing that has 2D pipeline (only x and y, z value =0) and 3 topo contour lines ( with x, y and z vaules). I need to divide the the 2D pipeline into say 2000 points and then get the corresponding z values from the topo contour lines. I think it can be done by interpolating between the z values for the two apparent intersection points of the 2D line and the contour lines, the x and y values will be the same for the points that falls between these two aparent intersections. Is there any lisp out there that can do that.
View 7 Replies View RelatedI am looking for an AutoLISP routine, which gives all aligned dimensions of a closed polyline, drawn in 3d.
I have attached a 2D drawing for reference.
The following gives me the first folder string, with no back-slashes, that the drawing exists in.
(setq FirstFolder
((lambda (/ tmpDir tmpPos)
(substr
(setq tmpDir (getvar "dwgprefix"))
(+ 2 (setq tmpPos (vl-string-search "\" tmpDir)))
(- (vl-string-search "\" tmpDir (1+ tmpPos)) (1+ tmpPos))))))
Is there a way to find the name of the second folder?
Is there a way to find the name of the third folder?
The string length of the characters for each of the first, second, third (and so on) folders are different, which means I can't count character using the "substr" function.
I have a list that contains data like this,
"Tree-01-08-AA5"
"Tree-04-12-QV"
"Tree-10-30-QS"
How would I go about sorting this list by AA5, QV, QS? I know how to use vl-sort and reverse, but I do not understand how I would go about this.
I have to go into approx 600 3D Models and rotate them all by 90.
I've just tried to search for a lisp that will do this to all of these files in one directory and can't find one. Something that will do this and save loads of time. I need to do this tonight so that these MEP files will all be ready for tomorrow morning.