AutoCAD VB :: Developing A Pdf To Dwg Converter
Jan 24, 2012i am using visual basic to develope a pdf to dwg converter.
View 1 Replies
ADVERTISEMENT
AutoCad :: Developing Contours For Noise Survey
Aug 15, 2012I was wondering if it is possible to develop noise contours such as seen in noise contour mapping. I understand one could just hand draft some polylines in but the degree of accuracy I would like to obtain would then not be sufficient. I have a grid based structure
currently on a topo map and have the measurements for each block (the blocks are a 10' by 10' area). From here I am lost to how one
would approach creating noise contour maps. Noise isopleths or in general creating measurement based contours?
AutoCAD Inventor :: Developing Spiral Flower Step?
Dec 12, 2011need to develop the Inventor part based on the autocad drawing. Its a spiral flower step for kids playground.
View 5 Replies View RelatedAutoCAD Inventor :: Developing Parametric Spreadsheets To Drive Modelling
Aug 7, 2013We are a transport engineering firm in Queensland and I would like to develop a spreadsheet that can formulate cross member distances and recalculate to add or remove cross members.
The basis of this is the overall size of the body we are building.
For example: The maximum width of a body in Australia is 2.5metres overall. Our cross members would be 6 mm shorter than the overall width of the body to allow for 3mm end caps to cover the open ends of the cross members. So the length of the cross member is width minus 6, or , parametrically the length is (overall width - (endcap thickness x2))
The body length is the tricky one. We have a maximum spacing on the cross members. This will vary from size of body to size of body. EG the spacing on the small 2 tonne body will be different to the spacing on the 12 tonne body etc. So lets say we want to have maximum spacing of 450mm and a minimu spacing of 300mm between centrelines of the cross members. The overall length of the body will also determine the number of cross members required.
On top of this there is the front and rear coaming to take into consideration.
So the formula would be ((overall length - front coaming - rear coaming) divided by cross member spacing)) then a check to see if the last space is what and then can we change the cross member size to take up that space without going over the maximum space. We would also need to take into account the width of the cross member section as well in this calculation.
EG if we have 150mm left at the end we could increase the cross member centres slightly to take up this additional space without going over the maximum space allowable.
AutoCad :: Developing Wrap-around Pattern From Cross Section View
Oct 29, 2013Attached is a simple drawing of a round tube sitting on an imaginary level grade. I'm needing to develop a pattern to cut the bottom angle. I'm making a scale model and this is one of the elements. The scale is 1"= 10.66" so this round tube will be 4.5" in diameter. The angle is too gentle to cut in my horizontal band saw; can't fit it between the guides. Years ago, we used to grid out from a base line and develop a continuous curved line on flexible linoleum that when wrapped around the tube, would allow a line to be drawn on what would be my grade level line.
We would then cut the steel tube with a torch on said line. Did this for 24" to 90" diameter pipes. I need to do this for this one cut; I think I can get all the rest of the angles for the project on the saw. I'm hoping that the printable (can be done on more than one sheet if needed and taped together or something) paper pattern can be rendered easily, such as a sheet metal shop might develop a flat pattern for rolling or bending. I'm limited to legal size paper, 8.5 x 17". I'm using AC LT 2011 so I'm limited in my abilities.
Paint Shop Pro :: Developing Raw Images
Apr 24, 2012Am I better off using the Olympus software to develop my images, then using PSP X4 to edit them? Regardless of which software I use to develop, why make any editing changes before I develop if I can then edit after I convert to a Tiff or JPEG?
View 3 Replies View RelatedLightroom :: Can't Load Photos For Developing
Feb 19, 2012All my dng's (with development changes) are visible in the lightroom library but they will not load when I want to develop further. This started after I tidied up my backup files.
View 3 Replies View RelatedLightroom :: How To Put Text Under Photos After Developing In 4.3
Feb 20, 2013How to put text under photo's after developing in lightroom 4.3
View 1 Replies View RelatedLightroom :: Developing Photos - Tone Curve Gets Reset?
Mar 6, 2012Installed LR4 today and ran into a problem.I have been working with alot of negatives lately and therefore my photos have a reversed tone curve. When I converted my existing catalog all looked fine, using the old previews. But when I go into develop on any of the photos the tone cureve gets reset to normal behaivour, and I have to redo the "invert". And all this using the old process (2010).
View 2 Replies View RelatedLightroom :: Retrieve Basic Developing Panels / It Just Disappeared
Aug 25, 2013how can I retrieve my basic developing panels it just disappeared?
View 4 Replies View RelatedLightroom :: Developing Image From Smart Collection Has No Adjustments - Immediately Unselected
Nov 25, 2012I am wondering if this could really be the intended LR behaviour? I start from a smart collection, one of the criteria is "has no adjustments".
Ok, as soon as I move the first slider in develop module, it no longer matches that criterion. But that should be no reason for LR to force me to immediately stop the develop edits on the selected image.
It immediately unselects, and I stay in Develop module with a grey window and the message "no image selected". (It does not move on to the next image, which still matches the criterion.)
I would expect that when I return to Library module, it would return to the same smart collection where I started, but I would not find my last developed images there, as they no longer match the criterion. But that LR grabs it immediately out of my develop selection?
Strange enough it stays the same, when I first explicitely selected all images while in Library/smart collection.
My expectation would be that I have this selection fixed to work on in Develop module. Similar to when I select any images from survey view and go to Develop module.
But no, the only workaround I found is:
Start from the smart collection, ctrl a to select all, then arbitrarily click on another collection withput this criterion - selection stays fixed - then move over to Develop module.
This is LR4.1 on Win7.
Definitely my functional specification would be: never take off an image from Develop unless the user moves on to another image. So ignore from where an image was picked.
Would you consider this a bug? Or a "feature"?
Do you see the same in LR4.2 or 4.3RC? Behaviour on a Mac?
Lightroom :: Developing DNG In 4.3 / Win7 64 (Catalog Sync Fails / Metadata Conflict)
Dec 17, 2012After upgrading to Lightroom 4.3 in Windows 7 64Bit I often get random problems during DNG developing. The first problem: LR during developing shows on image thumbnail the exclamation mark icon of "metadata conflict" warning (see attached screen snapshot). This problem occurs when an external program (i.e. PS) has modified the DNG file and LR Catalog is not synchronized. Of course no modification at all has been done externally by any software but LR itself! It seems a problem of DNG/catalog sync that in some cases fails (very disappointing). The second problem is the black exclamation mark (see again attached screen snapshot) that means problems during reading DNG!! This problem is absolutely random too. Developing is still possible on this files and usually the problem disappear ...
This problems don't affect proprietary RAW files (NEF from my Nikon D300s) and I've never seen them in Lightroom 4.2.
AutoCAD 2013 :: Developing Connected Piping System In 2013
Dec 3, 2013how can I develope a proper piping system just like the one in the attached picture in AutoCAD 2013.
As you can see the tubes aren't that greatly connected.
Each tube is blocking the pathway of the other tube.
I need them to be all connected.
The reason why, is because I will be later using this design in Inventor Fusion and Simulation CFD to have fluid in the tubes.
AutoCAD Inventor :: Developing Casting Models Into Machining Models
Oct 6, 2011We are looking for a workflow example of developing casting models into machining models.
Typically our castings are made from different materials (Fig-1) and then machining (Fig-2) are created from these castings.
Is creating the casting as an iPart (with different materials) and then deriving the machining from the casting the proper method?
Doing it this way seems to force us into making a machining for each casting material instead of just one machining that is an iPart. How should this be set-up for BOM purposes and for use with Vault (Base Version)?
AutoCad :: PDF To DWG Converter?
Jun 24, 2013i need .PDF to .DWG converter
View 2 Replies View RelatedAutoCAD 2013 :: DWG To PDF Converter
Jun 28, 2013I am trying to print DWG render to pdf. The pdf prints ok but it reverts back to wireframe instead of the render view.
View 2 Replies View RelatedAutoCAD 2013 :: Best PDF To DWG Converter
Oct 2, 2013I have been ask to supply a PDF to DWG converter on our CAD network. I wanted to ask around for what others are using for this and which might be the best one out there.
View 9 Replies View RelatedAutoCad 3D :: STL To Solid Converter?
Jan 15, 2013Any good STL to Autocad solid converter?
I have a old drawing that the original file got corrupted but I still have a STL model of.
AutoCAD 2010 :: DWG To TIFF Converter?
Nov 27, 2009Looking for the link to download a DWG to TIFF converter that:
Can convert big sizes (up to A0)
Can use high resolution (600 pixels)
Can use plot styles with Lineweights
Can convert to black and withe or gray scale.
Can convert embeded TIFs (logos)
Preferentially working within AutoCAD
AutoCAD 2013 :: PDF To DWG Format Converter?
Nov 2, 2012Looking for a pdf to dwg converter that works very well. I am recreating some old drawings with Inventor that are currently in pdf format and would like to convert them to dwg's simply so I check the missing dimensions using AutoCAD. I've seen several converters out there and have tried one. However, the converter I tried resulted with the dwg being created with short polyline segments.
View 9 Replies View RelatedAutoCad :: 2D Floor Plans - PDF To DWG Converter?
Feb 7, 2011I have some 2D floor plans and mechanical PDFs that I need to convert to DWGs so I can edit them.
Is there a reliable PDF - to - DWG converter out there that works?
AutoCad :: Converting With DWG Gateway PDF Converter For 2002
Mar 24, 2011Problem converting with DWGgateway PDF converter for autoCAD 2002.
Every time I try to convert my drawing in paperspace to a PDF, the objects in the model space do not show up. However everything on paperspace appears. The layers are not set to do not plot.
AutoCAD 2013 :: Converter For Bitmaps To DXF / DWG File Format?
Jan 30, 2013I want to convert bmp to dwg/dxf file so I can use in Autocad LT 2013. Any such program?
View 4 Replies View RelatedAutoCAD Inventor :: Solid To Mid Plane Surface Converter?
Oct 19, 2010Any program to convert 3D solids to a mid plane surfaces? We need our models in this form to do FEA work on them. I wanted to ask this question before I took on the task of trying to create one myself.
View 9 Replies View RelatedPhotoshop :: DNG Converter
Feb 18, 2013I downloaded and Installed Adobe DNG Converter because Lightroom 4 would not recognise the .NEF raw files from my Nikon D3200. When I subsequently plugged a card into the reader the PC produced USB sounds repeatedly. I had to shut down the PC in order to safely remove the card from the reader.
View 3 Replies View RelatedPaint.NET :: How To Use DDS Converter
Jul 8, 2013I am a sim racer and I used to use a DDS converter when I had Win XP. Now I have Win 7 and the converter no longer works. So..... I am using Paint.net now. It opens the file but you can hardly see the car. It has a checkered cover.
How do I remove this so I can see the car really well ?
Attached Thumbnails
Photoshop :: Where To Install DNG Converter
Dec 16, 2012I cannot figure out where to put the new DNG Converter. The download is installing itself in a folder (within PS5) but it is not recognized by the program at the time of use!
View 1 Replies View RelatedPhotoshop :: DNG Converter Not Working
Jul 25, 2012I have CS4 and just bought a D7000, realised it won't convert the RAW images to DNG. I have downloaded the latest converter but it is not seeing the images on the SD card or from a folder on the laptop. Have downloaded several times.
View 3 Replies View RelatedPhotoshop :: DNG Converter DMG Won't Open
Apr 9, 2013DNG converter dmg wont open.Downloaded to desktop, Mac, double clicked said not recognized.
View 3 Replies View RelatedPhotoshop :: DNG Converter 7.2 And Lumix G5
Jan 6, 2013I just installed DNG converter 7.2, which is supposed to work with my new Lumix DMC-G5. However, DNG converter does not see the Lumix rw2 raw files when I open a folder containing the files.
View 3 Replies View RelatedPhotoshop :: Pixel To MB Converter
Jan 13, 2005Accepted File Types:
The Photo Center accepts JPG (.jpg) and TIFF (.tif) files under 6 megabytes (MB) each. You may add up to 200 MB at a time. (Quote)
This is what i can uploading for 8x10 prints from my PS "creations"
i have several photos with many layers and some are less,and i was able to increase or decrease the pixel in each photo,to match the allowable (under 6 MB)
tolerance.is there a way to calculate the ratio from pixel to MG to my Max.allowed?
(basically i want 5.99 MB)
