I need to replace a large number (3700) of blocks with points, and cannot find a command for that operation. I have found a lisp for converting circles to points.
Have I just not found the command, or am I a bad googler? Unfortenately I cannot handle pure code (yet), so I need a lisp file (or the command).
Lisp Routine that could replace a line at a specified maximum length with a block at the lines midpoint.
I would love to be able to replace all lines I select which are say less than 0.5m in length with a block at the lines.
I am learning autolips and i found a problem that i can´t solved.
(vl-load-com)(defun c:pmb ( / ss ent pt )(prompt "
selec block : ")(setq ss (ssget '((0 . "INSERT")))) (setq ent (ssname ss 0)), (setq pt (cdr (assoc 10 (entget ent)))) (command "point" pt))
wich this code you select one block and insert one point at insert point´s block.
which this other code yo select all block and insert all point.... but in one block
(vl-load-com) (defun c:pmb11 ( / sele cod bloque nbloque lista pt ) (prompt "
block: ") (setq sele (ssget ( List'(0 . "INSERT"))) Cod 0 )cod (1+ cod) (repeat (sslength sele) (setq bloque (ssname sele cod)) (setq pt (cdr (assoc 10 ( entget bloque)))) (command "punto" pt) );repeat )
trying to insert point instead of block.
(setq blok (entget (car (entsel))))
(setq point (cdr (assoc 10 blok)))
(setq XX (rtos (car point) 2 20)) ;; x koordinata bloka
(setq YY (rtos (cadr point) 2 20)) ;; y koordinata bloka
(setq ZZ (rtos (caddr point) 2 20)) ;; z koordinata bloka
(command "point" xx,yy,zz) is not working
!xx="5582453.414999999" but when i (atoi xx) i get 5582453 no dedimals...
how to create valid insertation point from xx, yy and zz?
know a lisp routine that would insert a block @ a specific point on an arc? For instance if I have an arc that has a radius of 20'-0" & I want to insert a block at a set distance from the end of the arc.i could probably use the divide or measure command but I was hoping I could do it with lisp. I would also like to be able to move the object along the path of the arc at a specific distance.
View 6 Replies View RelatedI need a routine that inserts a point at the insert point or block named "Insert_Point" at every block in the file. The routine could use the current layer, which would be set prior to starting the routine. If it could request the user for the PDMode value and PDSize that would be great too. This will assist me in creating block libraries.
View 9 Replies View RelatedHow can I find a block with a specific name and get what the coordinates are? What we have is our Bill of Material is attributed blocks. I am attempting to change the first one. Well all of the lines that list the parts are seperate blocks with the same name. Now the Top Line of the Bill of Material is a different named block. If I can find the coordinates of this block I can then select the first line to do what I need to.
If needed: AutoCAD 2013 User using Visual LISP for editing LISP and DCL files Also I have AutoCAD 2011 currently still available for us, but we are using AutoCAD 2013 for 99.9% of AutoCAD use
I have insert blocks in my dwg. It is the circle. While creating the block, i was just pick the point into the circle not exactly at the centre.
Now i want change the insertion point of the block at centre of the circle without moving the objects from the dwg.
Beacuse i had use block editor to change the insertion point. But after changing, all blocks were moved from the original position.
I would like to create a lisp that places a block at a pre-calculated point. I've created a lisp that fetches me a block to place into my drawing. The only thing is
I have to point out the place i want it to go. I want it to got into the corner by it self. I would like to create a lisp that calculates, by the retrieved variable of the layout / paperspace, minus 10
from the bottom right corner. minus 10 from the bottom up and from the right edge to the left.
My multileader style uses a block as a content. How can I find world coordinates of insertion point of block entity within multileaders?
View 3 Replies View RelatedWe have several AutoCAD drawings with hundreds of block references inserted with imprecise coordinates. Now we need to dimension all elements and need to correct these positions.
I am searching for a routine to round these positions up or down towards a 5mm precision so I don't have to manually move every single block element.
Is there any way to automate the task or do you know any workaround (like inserting the elements into a drawing with poorer unit precision settings)?
I've have code to test if the insertion point is within a closed polygon. But prior to testing the insertion point I use ssget to trim the selection set initially..
(ssget "CW" Pnt_List (list (cons 0 "INSERT")(cons 2 BlockName)))
this requires that the whole Crossing Polygon is visible, so I do a zoom first. This requires time. Is there a way I can do this that does not require the zoom?
How would I go about this. if a two blocks or polygons are overlapping area?
A good method or the algebraic formula for a function to tell me if a point is inside a polygon or block's area?
I want to make a block which is visible to snap only on a special point, say pivot point.
View 7 Replies View RelatedI have a lisp routine that I would like to add to. Right now when running the macro the user is not prompted to "Pick Point On Line" in this example
(command "insert" blk "s" var1 pause pause))
I have added the line
(setq pt1 (entsel "Pick Point On Line "))
(command "insert" blk pt1 "s" var1 pause pause))
but the command doesn't seem to like my PT1 value
BLK and VAR1 are set in another lisp routine.
For a program i am working for i have to extract the base point of a dynamic block.
This can be done perfectly by this function:
(cdr (assoc 10 (entget (car (entsel)))))
But i want the entity selected based on a previous slected point. So for example when i selected pt1 (which is a point at the border of the dynamic block) i want to be able to extract the base point on the block whit this point.
is it possible to create a block so that the base point is the only snap point on the block?
In other words supose I have a block of a simple rectangle with the base point in the center.
If I try to snap to the block, I will be able to snap to all the corners, but not the base point. I know that i can put a point at the base point, but can I turn off the snap to the corners (just for the block) in other words, have an object that is unsnapable to without turning the snap mode off.
I was asked if there was a way to replace an embedded (Nested) block inside of multiple blocks, with another block. I thought of Express Tool's "Replace Block with Another Block", that that only works with blocks inside the drawing, not nested blocks. The only other way I know of is to redefine the block current block, then rename it to the new name.
View 6 Replies View RelatedConsider the following
(if (ssget "_X" '((0 . "ACAD_TABLE")(1 . "PIPE LIST")))(progn (vlax-for a (setq ss (vla-get-ActiveSelectionSet (vla-get-ActiveDocument (vlax-get-acad-object)))) (repeat (setq r (vla-get-rows a))(setq r (1- r) c -1)(repeat (vla-get-columns a)
(if (eq "*PL*" (vlax-invoke a 'GetText r (setq c (1+ c)))) (vlax-invoke a 'SetText r c "THREAD ONE END"))))) (vla-delete ss)));progn);if
Basically, it replaces this text inside a table:
1 1/2" NPTM - A53 - 3000LB - A-53 - 3000 LB
with:
thread both ends.
But I'm limited to the size of pipe, it's material and its pressure rating. I can't change how the text in the field is populated. It would be nice if, it did a search for NPTM, and when that string exists in the string, change it to "thread both ends".
Essentially right now, I have 46 lines (and growing) of different scenarios. I just want the NPTM to trigger the string change.
I am looking for something a lisp or program that would do a light point by point of fixtures in a plan.
[URL]
Is there a way to find and/or replace "very" special characters like [carriage return], [backspace] or even [tab mark], considering that the first thing that comes to mind when saying special characters is the standard and extended ASCII only.
View 4 Replies View RelatedReplacing characters in a text file.
I solved the following Lisp routine chore. I have this csv file of coordinates (and many more) that comes from a total station:1,100,100,10,50
2,100,200,12,50
3,200,200,12,50
4,200,100,10,51
and should replace the code after the last comma like this:1,100,100,10,.50
2,100,200,12,.50
3,200,200,12,.50
4,200,100,10,..50
To be able to generate the topographic map. And I have this code but does not work properly:
(defun c:cod (/ filename fileopenr readline)
(if (setq filename (getfiled "!!! SELECT *.csv FILE COORDINATE:... ¡¡¡" "c:/" "csv" 0 ))
(progn (setq fileopenr (open filename "w"))
(while (setq readline (read-line fileopenr))
[[code].......
I write a code to replace strings in one string.for example
str="AutoDesk, AutoCAD, 2013, Electrical, 64Bit"
patt=", "
NewStr=" - "
==> result: "AutoDesk - AutoCAD - 2013 - Electrical - 64Bit"
;;replaces NewStr instead of Patt(s) in Str string(defun ReplaceStr (NewStr Patt Str)(While (> (vl-string-search ptt str) 0)(setq Str (vl-string-subst NewStr patt Str)) );;whilestr) ; usage;(ReplaceStr " - " ", " "AutoDesk, AutoCAD, 2013, Electrical, 64Bit")
==> result= ; error: bad argument type: (or stringp symbolp): nil
I'm inserting blocks into my drawing and the block has a basepoint and a 0,0,0 point. The CAD guy who usually works with me is off today but he has a keyboard method of switching between the 2 points when inserting the block.
Its a fairly straight forward thing on his keyboard, nothing he has set up but standard in autocad.
I've had a try hitting a few keyboard buttons this morning but can't seem to do it.
We're using C3D 2013 SP2. The survey company we use uses point styles to show the blocks. Say they shoot a catchbasin. Instead of inserting the block, the point shows up as the block.
I did a field check & needed to insert a missed CB. When I inserted the block, the other points that were CBs disappeared. I had to insert the block, copy it the clipboard, undo the insertion & then paste the block in. It did this on other drawings & other blocks.
my problem is whenever i make a new block a stretch point appears even if its not a dynamic block . also its not a stretch point, because when i click on it, it just move the block , and it always appear on the coordinates 0,0 it cause me a problem when I insert the block , autocad use this point as a base point , and its very far from the real block .
View 1 Replies View RelatedIs there a way to create a block with attributtes that automatically complete x, y, z, lat, long for the insertion point of the block?
I am trying to complete text in paperspace that will automatically fill in the lat long of a point in model space without using a table. I have tried field insertion with reference to a cogo point, but it doesn't give options for position on a cogo point. If I pick a block with attributes, it will let me pick any attributes, and x,y position for the block.
Cogo points show all the information I need to propagate in the properties....but how do I get that to translate into the text using fields or some other method?
Dell Precision T3600 - Windows 7 64-bit
NVIDIA Quadro 600
Intel(R) Xenon(R) CPU E5-1607 0 @ 3.00GHz 3.00GHz
8 GB ram - Two 1TB raid
I want to move the base point of a block in the block editor. However, when I move it, the block moves accordingly in the drawing.
How can i move the base point in the editor, so that the block stays at the same position in the drawing.
I get an AutoCAD drawing from my conveyor manufacturer who have buried a block (tagname) in all of their conveyor blocks.
The only way to remove them is to manually use BEDIT and erase the tagname block.
Is there a way through Autolisp to search all blocks in a drawings and if the tagname block is part of the definition of the conveyor block, erase the tagname block or redefine the conveyor block without the tagname block.
When dynamic blocks are inserted they're assigned an anonymous block name. I'd like to be able to retrieve the name of the parent block after selecting the block on screen using AutoLisp.
Need a bit of code that handles this?
Create a routine that looks for a block based on a portion of that block name, using a specified path or search path.
For example, block to search for is BLOCKABC123, so if someone inputs ABC or 123 as a block name, it will locate that block within that folder and inserts it into the drawing at a user specified location.
Ideally, if there is a check in that if it finds more than one match, then perhaps it flags or prompts you to choose 1, 2, or 3 option which block to use. But I can live without this special function if it requires too much time to code.