AutoCAD LT :: How To Get PREVIOUS PLOT Option To Be Default In Plot Menu
Jan 20, 2012I am using AutoCad LT2011 and would like to know how can i get the PREVIOUS PLOT option to be the default option in the plot menu.
View 5 Replies
ADVERTISEMENT
AutoCAD Visual LISP / AutoLISP :: Plot Transparency Option In PLOT Dialog Box
Sep 11, 2012Where else do they keep this setting? I only have found it in Active Layout in extended dada
(entget (vlax-vla-object->ename(vla-get-activelayout (vla-get-activedocument(vlax-get-acad-object)))) '("*"))
The last pice of extended data is:
("PLOTTRANSPARENCY" (1071 . 0))
When i change it to 1
(setq layout(vla-get-activelayout (vla-get-activedocument(vlax-get-acad-object))))
(vla-getXdata layout "PLOTTRANSPARENCY" 'type 'data)
(vlax-safearray-fill data '("PLOTTRANSPARENCY" 1))
(vla-setXdata layout type data)
it stays there (extended data), but the setting in Plot dialog box doesn't change!!! And it still prints no transparency.
It takes to save the drawing and reopen it again to see the change.
The command -PLOT does not have this setting as well, so my options back to VBA or Lisp, but HOW?
AutoCAD 2010 :: Plot Thin Lines And Dots When Plot Transparency Option Is On
Feb 6, 2012I have a problem to plot thin lines and dots when Plot Transparency option is On in the Plot dialog box.
The lineweight is a half of the original. I think i have tried everything.
It shows correctly in the Plot Preview but when printed there are no dotted hatches and lines are much thinner.
AutoCAD Print / Plot :: Change Plot Setup To Multiple Sheets For Use With Batch Plot
May 21, 2013I have one drawing per file at model tab. When I need to plot a multiple page file, I use:
Print > Batch Plot.
The problem is that I have to set plot configurations ( plot style table, plot area, paper size, etc) in each file before use Batch Plot.
Now I received 722 files with a wrong Plot Style Table. For this time I change the associated *.ctb file at Plot Style folder, but I will need to associate the right *.ctb to each drawing. It's also common to have to change other properties.
AutoCAD 2010 :: Previous Plot Portion Not Shown Shaded In Layout
Dec 9, 2012I am using autocad 2010 in layout have more than one drawings when i give plot from layout and after 2nd drawing give plot from same layout that time the previous plot portion not shown as shaded. in autocad 2008 previous plot portion shown shaded in layout.
View 2 Replies View RelatedAutoCAD 2010 :: Shaded Plot Option
Dec 16, 2012i want to know how to enable those options for shaded plot.
View 1 Replies View RelatedAutoCAD Print / Plot :: Mac Doesn't Allow For Proper Printing On Their Plot Style Setting
Aug 29, 2013I am a Mac user and new to AutoCAD. I am enrolled in a CAD class this semester and the instructor for my session is requiring Windows. Supposedly this is because AutoCAD for Mac does not allow for proper printing on their plot style setting.
I understand that I can install Bootcamp and Windows on my computer, but I'd really like to avoid that if I can. If I were to do my work on my Mac and then digitally transfer my files to a PC for printing purposes, would my files become corrupted or compromised in any way?
AutoCAD Print / Plot :: Sharing Plot Files 64bit With 32bit Machine?
Aug 21, 2012Can users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?
View 1 Replies View RelatedAutoCAD Print / Plot :: Publish To DWFx Plot Stamp Layer
Aug 29, 2011When I publish a drawing as a multipage DWFx (or PDF for that matter) with "Include Layer Information" selected, the Plot Stamp (Simple Date/Time and Text) comes out but on different layers on different layouts.
Example:
First Layout : Plotstamp resides on Layer 0
Second Layout: Plotstamp resides on Layer 3P
Third Layout: EQPT-VC
etc
Some general information:
Autodesk AutoCAD 2011 64bit
Autodesk DesignReview - 2012
Adobe Acrobat X Professional
Layer 0 Is thawed/plotable and on in all layouts, viewports all layers, viewports. It has at least one entity per layout
Is there anyway to rectify this and still use the built-in Plot Stamp?
AutoCAD Print / Plot :: 2007 Not Reading Plot Styles Correctly
Jan 17, 2012So the firm I work at has AutoCAD 2000 and 2007. 2000 is installed on 5 out of the 7 computers, and 2007 installed on 6 of the 7 computers. 2 of the computers running just ACAD 2007 are Windows Vista, while all the other computers are Windows XP. We have an OCE TDS320 CAD Printer, an HP Wide Format Printer and a Panasonic 330 Copier/Fax/Printer. Our Problem is that When you try to plot an ACAD2007 drawing it will only plot it in color. This problem did not exist before 1/12/12.
When I select the Plot Style to print I select "monochrome.stb" which has always worked, now all of a sudden it doesnt. The only way i have found to fix this problem is to change my drawing to layer "0" which is white, so when it tries to print in color it will print black. Another Guy in the firm i work at has ACAD2007 on his computer running XP, he also has 2000 running on the same computer. When he tries to plot on ACAD2007 the same thing happens, so it is not isolated to my computer.
There is a difference though between his Plot Styles on his computer and the ones on mine. His end with .ctb, which works. It only doesnt work when he tries to print a drawing i made off of my computer. Because of this we copied his Plot Style folder for AutoCAD 2007 and installed it into the folder with all of my plot styles on my computer, replacing the ".stb" with ".ctb" That did not work at all. The last thing we tried was to copy over a file that plotted correctly, delete the drawing and draw what we needed, This also did not work. So basically we are thinking that ACAD2007 is not reading the Plot Styles correctly, or the Plot Styles are wrong or currupt.
AutoCAD Print / Plot :: Plot Results From Paperspace Are Different From Model Space?
Jan 17, 2013I have several objects on various layers in model space and they are exposed through a viewport in a paperspace layout. I also have a corporate CTB plot style.
Here is my problem: If i plot the objects from model space, they all plot with the correct lineweights as defined in our corporate CTB, but when i plot them from the paperspace layout, some but not all objects plot with a heavier lineweight than what is defined in the CTB.
I thought the CTB was supposed to override any settings applied to individual objects, but more importantly, why the different results, on the same objects, depending upon the space from which they're plotted?
AutoCAD Print / Plot :: Publish Vs Plot - Image Shifts And Border Cut Off
Aug 13, 2012I have found that when I Publish, the drawing comes out shifted about 1/8" down and 1/8" left as compared to when I use Plot. Which of course is just enough to cut off the sheet border which is 1/2" from the paper edge. I am using the same Page Setup for both Publish and Plot, same drawing.
This is to an Oce TDS600, and it only happens with 15x21 paper size. All paper sizes are set to 0" border. Probably an Oce issue, but have any of you seen this before?
AutoCAD Print / Plot :: Poor Plot Quality With Aerial In 2012?
Aug 8, 2012I recently upgraded from 2010 to 2012 and when trying to plot, using the very same page setups as before the upgrade, the quality (or resolution) of the plot is very poor and pixelated. I am using very high resolution aerial imagery. The output is not at all high resolution (totally pixelated, not presentable as professional). It seems like AutoCAD is reducing the image quality now. Is this a system variable that can be adjusted?
View 1 Replies View RelatedAutoCAD Civil 3D :: Station Ticks Display In Plot Preview But Do Not Plot
Nov 29, 2012I have a stationing line. I've used the block PTTICL to make ticks. The ticks display perfectly. I'll run through a plot preview and the ticks show on the plot preview. I push plot go to the printer and the ticks are not plotted.
I've checked the layer. They are on a layer that should print.
I've checked the block. The block is created on a layer that should print.
I've run through a number of options regarding the alignment label properties and found "display" to be equal to "true."
Everything else plots just fine. Only the station label ticks refuse to plot. My project is fairly short so the work around was to put a poly line right on top of the tick mark.
AutoCAD Civil 3D 2013.
AutoCAD 2013 :: Get Batch Plot To Plot PDFs To Single File
Sep 30, 2013I have just switched over to 2014 and i cannot for the life of me get my batch plot to plot PDF's to a single file! Instead, it's printing all 37 layouts separate. I tried switching between multi-file & single file in the publish options, but nothing!
i know that it took me a while to perfect my settings the last time i set up a new version, but i am struggling to work it out now.
AutoCAD Visual LISP / AutoLISP :: How To Add Cadfile Plot Date And Plot Time As Attribute
Aug 30, 2012I am aware of the plot stamp available in the Plot Dialog box, however, we are looking at ways to imbed this info in the dwg. I currently have the WD_TB with an attribute for FULLFILENAME, an attribute for PLOT DATE, and an attribute for PLOT TIME12. So I get the information on the dwg. I would like to be able to run all these attributes as a string. I have tried FULLFILENAME|PLOT DATE|PLOT TIME12 with spaces, commas, ( ), " ", etc. and I do not know the proper syntax to get this to work. I have also tried (getenv "FULLFILENAME") or the getvar, in the title descriptions box.
View 1 Replies View RelatedAutoCAD Print / Plot :: KIP 3100 With 2011 Heidi Driver Crashes Upon Plot Preview
Sep 1, 2011AutoCAD Architecture 2011
Windows 7 x64
8GB RAM
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
Using the non-AutoCAD driver works.
AutoCAD Print / Plot :: Cannot Choose Plotter In Plot Manager
Jun 25, 2013In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to "None".
The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.
I tried to add this plotter through "Add-A-Plotter Wizard", but each time I obtain an error massage "Autodesk Hardcopy component failed..."
[URL]
AutoCAD Print / Plot :: DWG To PDF - Lines Plot As Gray Instead Of Black?
May 9, 2011Unfortunately I am using ACAD 2000 so bear with me and the only ACAD training I have is a 3 day crash course at the local software reseller.
I am attempting to plot a drawing that was created from a template into a .pdf but it is plotting colored lines instead of black lines.
Here is some background info. My template is set up as a .dwt which I will save as a .dwg when I begin to make my drawings. Plot style table is “monochrome.stb” and I have selected Adobe .pdf as my plotter configuration. I then select the “Properties” then go to “Custom Properties”, “Paper/Quality” tab and then select “Black & White” as my color.
When I go to plot the drawing as a pdf and do a preview of what I am about to plot, I see that the lines that make up the drawing are a shade of gray in color. All my lineweights in the layers property manager are set to default. I have attached a blank drawing that is based off of my template.
AutoCAD Print / Plot :: 2004 - Set To Plot To File / How To Change
Aug 14, 20122004 and how to turn "plot to file" off? Any time they go to plot the plot to file is already set and grayed out. It has been way too long since 2004 and I don't know where to have them look although I assume it is in Options somewhere.
View 2 Replies View RelatedAutoCAD Print / Plot :: Application Terminates When Plot Command Is Given
Apr 27, 2012I'm using autocad 2011 LT License version 5 users & autocad 2012 Lt License Version 5 users.I have got a HP Laserjet 5200 printer, when i give a plot command from one of the workstation having autocad 2012 lt
the application gets terminated automatically every time.This issue is only with a single client having 2012LT all other autocad LT 2012 workstations in the same network plots w/o any complaint.
AutoCAD Print / Plot :: Layers Turned Off Plot Unless They Are Frozen?
Sep 13, 2013I have a user which we just installed Autocad Civil 3D 2014 on his computer that is running on a Windows 7 64-bit OS. However, he has had the same problem with Civil 3D 2011, 2012, and 2013 ever since we took him to 2011 in September 2011. So, it is not something new. It may have been around before then but my companies common practice back then was to freeze layers with a script file before plotting. While attending a class back in 2010 or 2011, he and his group were told to “do not use FREEZE on layers in Civil 3D” since things frozen did not get updated like they would if they were just turned off. So, they have been using the “ON/OFF” commands on all Civil 3D files since then.
Here is the problem:
A drawing, typical of this and other jobs he does, has a title block which is an xref in paper space and the site plan xref in model space. He can turn "OFF" certain layers from the site plan as viewed from paper space to remove clutter and then go to make a plot. After getting it set up to print and going to the preview the layers he has turned off appear in the preview and if he goes ahead and makes the plot or PDF those layers that were turned off will plot out.
The work-a-round they have been using ever since has been to go back into the file(s) and “FREEZE” the layers that were turned off, make the plots and then go back and “THAW” the layers before ending the drawing.
Things we have tried:
Set Visretain=1
Used the “Publish” command.
Set Layerevalctl=0 or 1
Is there a way to use ON/OFF instead and have the layers NOT plot out? OR, is this something that AutoCAD will not do regardless? Has it always been that way and we have been unaware of it through the past four releases?
AutoCAD 2010 :: Why Does Normal Plot Style Plot In Color
Oct 9, 2013AutoCAD - Why does the Normal plot style plot in color? Black seems to make a lot more sense. Almost everyone in Architecture uses black prints most frequently so that should be the default. And you can't adjust Normal to all black. So what was AutoDesk's reasoning?
View 9 Replies View RelatedAutoCAD Print / Plot :: Delay In Plot Manager Window
Feb 18, 2013I have a network with Windows XP and Windows 7.
Printers: from HP 5000 series to a KIP 3000.
CAD,from 2008 to 2012 versions.ALL of the PCs are having this strange behaviour:Open a drawing, Press File then Plot and..
Scenario 1: if the KIP3000 is online then plotting window comes in few seconds, a normal, decent delay!
Scenario 2: if the KIP 3000 is offline then plotting can be delayed to minutes!!!
Downloaded the drivers from KIP web site, installed and tested, prints fine once the above issue with delay is sorted! I’m guessing that is something built-in CAD, pre-emptive, background checks running for printers status when you attempt to plot to the printer / plotter !
AutoCAD Print / Plot :: How To Adjust Grayscale In 3D Model Plot
Sep 28, 2011I need to plot a drawing with a few plans, which are in 2D but also a 3D model of the intire installation and a few side views, which are side views of the 3D model.When I plot the drawing I am able to get the side views in black and white by taking the following steps:(i got these steps from this post: URL....
- set the visual style (in model space) to hidden or wireframe.
- in the layout you select a viewport that conntains a 3D visualisation and double click in that window to set the visual style to 2D wireframe and also set the viewports shade plot to hidden.
because the plotter is black and white only I see those side views in different shades of grey but the problem is that the difference in grey isn't clear enough (and yellow pipes are hardly visible) and I can't adjust these. When adjusting the .ctb it only affects the 2D views and not the 3D views.
It is possible to change the greyness by changing the color of the diffent pipes that are in the drawing but this is not a desired option by the client.how to alter the shades of grey in 3D visualisations so that not all pipelines look the same .I attached a file of what the plot preview looks like and another of what the actual plot looks like
AutoCAD Print / Plot :: Pixelated Plot Of PDF In File When Printing To PDF
Apr 8, 2010I am plotting a file that has a pdf referenced into it. The quality of the plot is degraded only at the inserted pdf. The rest of the AutoCAD file looks fine. The inserted pdf is a printed AutoCAD file which looks clear and even has embedded layers and linework I can snap to (which seems to indicate that there is vector information present when it is in Autocad.
I have attached an image with 4 zoomed-in screen shots to show what I'm describing.
AutoCAD Print / Plot :: 3D Drawing Won't Plot In Black And White Using CTB
Nov 21, 2011We do most of our drawing in 2D – quaint I know, but that’s the way the office works. On occasion we’ll do something as a solid model to guide a client understand a complex roof or a clearance problem. We started a model for a project we are working on and ended up using it as building elevations.
The problem is with plotting. If I use our standard office CTB (which is set to print as black), I get color printouts no matter what I try. I have tried using an STB and changing all our layer colors to “7” in an attempt to make it print black, but I'm getting extremely undesirable - seemingly random - line weight results.
The client wants the next project done in 3D as well and I’d like to be able to have the elevations look right.
AutoCAD Print / Plot :: Apply Plot Styles To Drawing
Apr 15, 2013Is there a way to apply plot styles and line weights to a dwg file like 'dwf ePlot' does but keeping the results in .dwg format?
View 4 Replies View RelatedAutoCAD Print / Plot :: Can't Plot To HP Officejet Pro K8600 From 2007
Jan 5, 2012I can't plot to my HP 8600 from Acad 2007, the plotter lights blink an error and nothing plots. I can save the dwg as a PDF and print the PDF to it fine. Is there a special plot driver for the 8600 or what am I doing wrong?
View 5 Replies View RelatedAutoCAD Print / Plot :: Arabic Fonts Jumbled After Plot
Feb 21, 2011Arabic Fonts Jumbled in Autocad. When i see in autocad it look very clear, when i see preview also, it is very clear.When i plot drawing, it is coming Fonts Jumbled.
View 5 Replies View RelatedAutoCAD Print / Plot :: Batch Plot To Printer Via Publish
Jun 28, 2012Been attempting to batch plot numerous dwg files to a printer via publisher. Has been successful on 2010, however experiencing difficulties in 2012.
Method used
open dwg file
set page set up to that required
save down dwg
print>Batch plot
add rest of dwg files to be plotted
remove all layouts to retain only Model Space
Highlight all dwgs
Select page set up from currently open dwg file
Publish
Result - only active dwg prints