So I am trying to create a lampshade that has holes in it for leds along the wall thickness. This lampshade only needs to be a few inches, but I am having problems cutting holes inside the lampshade, and then revolving them to make multiple holes.
View 4 RepliesI have created a Hollow Cylinder using Polysoild (Object Option). I want to drill holes(array) on the cylinder.
View 9 Replies View RelatedLooking for example macro that can create a new sketch, add a few lines and arcs, Then revolve the sketch around an axis to create a solid part. For example a shaft?
View 2 Replies View RelatedI have a model that has been made up from a revolved sketch and then had loads of bits done to it etc.. Basically it is a tapered ring with a fillet on the top edge, I need a top face dxf export for profiling and to do this I need to remove the radius on the edge, but because it is a revolved sketch and it is not filleted it is not so easy to do with other references involved.
Is there a way I can temporally rebuild the edge to remove the fillet, I tried in fusion but it won't allow a Zero fillet edge?
I can't upload the sketch to show you unfortunately.
I'm really struggling with constraining a weldment assembly. I've attached a JPG of the Assembly but I cant get the constrains to go where I want them.
Basically this assembly is a wheel with three equally spaced stays welded to a large nut hub. I have constrained the center axis of the wheel to the center axis of the Nut so the wheel and nut will remain aligned.
What I'm struggling with is constraining the three stays to the wheel and to the nut equally spaced around the nut.
Is it possible to apply a tangent constraint to an edge of a cylinder at an angle to the revolved side of another cylinder? I wan't to avoid applying a specific angle constraint if at all possible.
View 3 Replies View RelatedI have 2 sheet metal parts, both have been revolved using an angle of 359.9deg so there is a small gap to weld. in the assembly I copied one as a surface onto the other part and I want to scuplt it at the intersection of the two.
The problem I've come to is that the small gap in the surface is preventing me from deleteing the upper part of the cut, how can I make the surface a whole so there is no gap in the cut?
I'm playing around with a part that I'd like to "decorate" with embossed features or perhaps even cut-outs. The actual part, before adornments, looks like a funnel. As sketched now, I'm revolving a spline and then creating a thickened solid feature. I suppose that the variable diameter and varying cross sectional radius of my part increases the level of complexity of this task over a part that looks more like a regular cylinder. I'm hoping to learn a tecnique that will work for revolved parts with highly irregular profiles - not just plain ole cylinders.
So, what I'd like to do is emboss (negative or positive) and/or thru-cut decorative geometric or vine/flower inspired patterns into the outside face of a funnel-like part. (Pic attached.) I'm picturing some sort of pattern that might repeat around the part. (The variable diameter probably really complicates matters here.) I haven't put much effort/experimentation into this yet - pretty much because I'm a loss about where to even start.
I need to shell out a Loft in the attached IV 2012 part file.The Loft i tried also as a new solid but the shell also cuts into the cylinder ( revolution 1 ) . I only want the 2 sides and bottom of the Loft to be Shelled, not the cylinder. What do i need to change to get the shell to work?
View 4 Replies View RelatedI'm loft retarded. What I did here was loft to a tangent work plane, then did a sketch on the top surface and extruded the shape that I want. There has to be a better & easier way.
View 9 Replies View RelatedI have a cylinder on top of a curved surface; I want to make the cylinder land adaptively to the surface, so I projected the circular face of the cylinder in the surface, which ended up being a 3D sketch. I tried to loft a solid between both curves, but it always gives me errors. Some examples are:The attempted operation did not produce a meaningful result. Try with different inputs.Multiple disjoint loops found in a profile section.
I have had success when trying to do the same thing with curved surfaces in two dimensions only (e.g. extruding a 2D curve), but I think the error is produced since the curved face I am trying to use belongs to an elipsiod.
Okay I've been building random things to teach myself how to use Inventor and right now I'm stuck on a rim I'm creating. My question is.. is there a way to copy and paste a lofted item since there are three parts to it (2 planes and 1 guide) because I need 4 more spokes and if I copy the loft it copies all three parts seperately. Then when I paste and orientate the small end of the loft to the plane I want it tells me "Unsatisfied Geometric Inputs".
View 4 Replies View RelatedI am having trouble trying to get the Loft-1 to run the same shape as Revolution-2 .Picture 1-1 shows how Loft-1 is slightly off centre to Revolution-2 at the top .could i model the Loft-1 and Revolution-2 using different tools in one command making it a smooth shape. Another problem i have is how do i make Revolution-2 at the end terminate into Revolution-1 smoothly.I tried using Loft but it kept getting fail message.Picture 1-2 shows where to terminate the end into the Revolution-1 body.
Inventor 2012
I have created a loft from 4 different sketches. Now I want to make a drawing with the front, side view and the dimensions of the 4 profile sketches from the loft. But I can’t find a way to put the sketches from the part on my paper. It works with copy-paste ;^) but this is not the way I want it (it’ll not change when I change the profiles in the part).
View 6 Replies View Relatedthis message appear with "loft" between blade sections the attempted loft operation resulted in self intersecting surfaces.Try with different inputs
View 9 Replies View RelatedI was wondering if it is possible to make a surface loft go from 1 square section to 2 round sections.
So 1 ingoing section en 2 outgoing sections.
I've attached a simple drawing.
I am following the U-Tube exercise called "Emergency Light (Cabinet) volume 1". I am at time stamp 1 hour 26 minutes, exactly.
In the video they use a Loft command in order to cut a shape out of two sketches numbered 10 & 11. I have been copying exactly and am having difficulty at this stage of the model.
Is there any reason why I am managing to use the Loft command earlier perfectly but not at this point.
Using the image below, I want to removed the yellow extrusion up to the red circular edge, I assumed split tool would do this.
And I don't require this but i would like to show the splines on the ends to "feather" out to the round like the actual axle does. (this is just for aesthics) I have the extrusion done, But I can't figure out feature is requied to do this, loft?
I have a part that I'm trying to loft using 3d sketches for the rails will this work? Everything is fine till I try to add the rails, As you can see the loft works with out the rails.
Windows 7 x64
IV 2012
Im struggling coming up with a loft or sweep to get the design effect I need. see on the pic how the profile terminates to a point.
View 4 Replies View RelatedI'm trying to produce this loft but the rail I really need it to follow won't produce any results. The other ones on the 3d sketch will work just fine but not the regular sketched one. It seemed to work when I made the rail a straight line but I need it to follow the edge of the surface which is a line, tangent to small r3 arc, tangent to line and connected through projective geometry from the original surface sketch.
View 2 Replies View Relatedhow to loft from 2d sketch to circular surface.
I have attached the model in this model I tried to loft Sketch 6 to Sketch 19.
attached are 3 files that demostrate what is happening when I select a profile to loft and the rails of the Surface and how it changes the profile and how I can get a straight back edge not bowed in like it did to the front
View 4 Replies View RelatedI want to create a solid using VB and loft definition.
I creat each time different planes that have a constant distance in x dimension and a steady rotation each time φ (deg).
On each each plane i sketch the same profile and that is happened for 360 deg.
The problem is that Loft is not made because a line of the profile must follow a line tragectory and all other points must follow a circular tragectory. Also, there is a problem from 180 deg to 360 because there is intersection of profiles.
The result must be a solid similar to snail shell but all the same solid, as a cylindar whith a half sphere in the bottom.
In the attached sample file if you edit the sketch in the first surface feature and change the dimension of 600 to 700, both the patch and loft features fail. It seems to be the curved edge that is the problem in both cases.
I cant see anything wrong with either way of modelling this so assume its a bug.This causes other problems in my real model with parts that reference these types of surfaces falling apart further down stream and is wasting heaps of $$$.
I made this part, which is a loft consisting of five symmetric squares. I plan on laser cutting each side, which would be exactly the same.
I can't seem to figure out how to make a flat projection of one of the sides. I have tried in sheet metal, but I don't use that feature in my line of work.
I am trying to loft a port shape for a project. I have been able to loft pretty much the same thing when part of a larger model but this time around it keeps giving me an error.
In the past i will loft the whole part then remove the inner portion to get the port.
I work at a car seat company, and we are just now, starting to draw in Inventor. I have problems drawing the seat belt. Here is my first try:
I have tampered with this one! From this angle it looks ok, but it isn't right. I have tried using Loft and Sweep, but with no good results! The seat belt is static in the shown position, but should be able to adjust onto another seat.
I am having to model a spiral slide in sections, and the top piece has this weird angled lip where the opening distorts. Im simply trying to take the face of the extruded part (in three sections) and loft it to the sketch on a different plane. And use the sketched curve as the centerline.
View 5 Replies View Related-Did I do the rectangular pattern correctly? If not, the correct one with step-by-step information
-Why the holes do not go through the thickness of plate?
The rotor is composed of cylinder and a solid lofted between two 3D profiles. The attached part file is correct. To reproduce the error- change the "inlet_width" parameter from 12mm to 10mm or less (it is a parameter in "Blade Profile" sketch). On updating the part there will be infinitesimally thin solid layer on outer diameter of the cylinder.
-3D Sketch profile is a projection not from the "Blade Profile" sketch, but from a plane offset from it. This was first attempt at a fix. I suspected the original tangent work plane to intersect the cylinder.
-Creating a new solid body from loft was the only way to avoid errors such as "non-manifold solid".
I will be creating multiple versions of this part and I need to be able to safely adjust the "inlet_width" and "outlet_width" parameters. I will be grateful of any proposed fixes/workarounds to that glitched behaviour.
EDIT: The version is Inventor 2014 Educational.