I patterned features but the material did not come along for the ride. I know I can change the material manually after the fact but I am making a parametric design so I want this to happen automatically. How do I do this?
View 5 Repliesmy create a circular pattern in an assembly that maintains the orientation of the part being patterned.
This is for foundation plates. There are 3 plates. The plates are square, and have bolt holes in the corners of the plates. Since there are 3 plates and its going around a circle, the angle between the plates is 120 degrees.
Now, Ive been trying this for some time now and what is happening is the firs plate is fine, but then the second and third plate are rotated around their center axis. I would like it to simply remain as inserted and constrained within the assembly.
I have attached a picture to be more clear about what I want and what I'm currently getting.
Is it possible to assign hatch patterns for material styles? I need IV13 to draw Ansi32 for steel and Ansi31 for Aluminum automatically.
View 4 Replies View RelatedI am completely new to ilogic but would like to make a rule in my idw file that change the hatch pattern in a section of a specific material.
Short Version:
I have an aluminum extrusion part. Material is set to Aluminum-6061. In any section view of this part I want the hatch to be ANSI 31 with a rotation of 45 degrees and a scale of .02 How do I do this?
I would like to know ih which way could make hole pattern on solid material when draw model? Precisely, PC monitor on back side. Monitor has little holes and stripes on the cover to use for ventilation.
View 9 Replies View RelatedI can delete every unused material except one in the Material Editor.I am trying to make the custom Material library and somehowI have got the Material I cannot delete. URL....
View 9 Replies View RelatedI am in the samill building buisness. While designing I thought it would be nice to show logs on our equipment. Is there anyway to show bark on drawings to show the texture on the final drawing?
View 1 Replies View Relatedwhere could i find a pattern overlay/pattern of holes for a metal floor.
View 9 Replies View RelatedHow can I make a circular pattern of a single occurence of a rectangular pattern?
A shaft has a rectangular pattern of holes (along its axis) on its surface. I want to pattern the 4th occurence of this hole pattern as a circular pattern? Can I do it in Autodesk. I can not select the a specific occurance of a patterned feature to pattern it again.
As you see in the template photo (the photo was scanned by Microsoft Security Essentials, healthy) I wanted to extrude my circle, and I made 28 pieces with circular pattern feature; now, do I have to choose all the pieces by one by to be able to choose all?
The sum of the problem: while using the Circular Pattern feature or rectangular pattern feature in Inventor, sometimes I want to extrude (join) or cut the drawings that I made (augmented) with using circular pattern feature, rectangular pattern feature. in this case do I have to choose all the augmented members one by one (for instance I make 42 augmented members), it can take a lot of time.?
How is it possible to use "Feature Pattern Select'' to make the Pattern a want in an assembly?
View 9 Replies View RelatedIs it possible to take a feature created by a pattern and reuse it to create another pattern? I have a circular part on which I have created a linear pattern (using the rectangular pattern feature) of holes, 6 in total listed as 3 ccurrences. if we number the holes 1-6, I would like to make a circular pattern based off holes 2 and 5. I have been unable to figure out how to select the individual "occurrence" related to the hole once in the pattern feature. If I create the circular pattern first and then the linear and try to suppress the others it supresses both holes in the occurrence.
View 4 Replies View RelatedI am creating an assembly with my base part being a weldment. I've added other components that mount to my base part. Now I need to add fasteners to the mating components. I have added my first fastener and now want to pattern the said fastener using the "Pattern Component" and by using the "Feature Pattern Select" option and selecting "Associated Feature Pattern". At this point I have already selected the component that I want to pattern and selected the "Associated Feature Pattern" to select my base pattern. The only problem is that I am unable to select the pattern desired.
A note on how my Weldment was constructed -The holes were created in the "machining" step of the weldment, not in the individual part before it was placed in the weldment assembly.
If I move the hole feature and its pattern to the individual part and then place it in the weldment assembly, I can then create an "Associated Feature Pattern" in my assembly file.Why can I NOT create the associated pattern when my hole features are created in the weldment assembly? Or am I missing something?
I have an assembly which I am using as a icopy component. In the assembly I have the adaptive sketch which os used for the icopy function and a part which is adaptive to the sketch. I then have the part pattern itself in the assembly. The problem is the pattern will not update when changes are made unless I edit the pattern. The pattern references parameters from the sketch so that when the sketch changes the pattern should change. It works but the pattern will not update unless i open the pattern to edit it. Is there a vb function which will force the pattern to update when a change is made? I tried the update document vb functions but no change. I will try to get a sample together that is a smaller file size so you can see what I am talking about.
View 2 Replies View RelatedCan't seem to locate the Inventor Material Library....under Default in Projects, the Inventor Material Library is highlighted in Red. Where I need to browse to inorder to locate it?
View 2 Replies View RelatedI am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
Is there a way for the scale to be correct to the drawing?
View 1 Replies View RelatedI changed the material using the vb.net code shown below.but after changing material the object is not updated ,the volume and mass didn't change .
Dim oDoc As PartDocument
oDoc = inventorApp.ActiveDocument
Dim oDTProps As PropertySet
oDTProps = oDoc.PropertySets.Item("{32853F0F-3444-11d1-9E93-0060B03C1CA6}")
[code]....
How to make a type of material go in one direction or by another degree . Ex: if you click on a wood type material, it goes up or down and right or left depending which side of that object is. On the picture below, it goes up and down, side to side no all sides go in one direction. I need to know how to mange the direction of the way of where the material go.
View 7 Replies View RelatedIs there a way to export a Inventor .iam/.ipt to .stp/.sat and keep material property and center of Gravity?
Is there any "external" format that will keep these properties?
We are a mid sized company the builds our parts from raw materials. Steel Coils, Steel tubing, Steel plate, etc.
We are have been migrating from MDT to Inventor over the last few years. We are now trying to implement Vault and integrate that data into our ERP system. We would like to model a part and assembly and check that into Vault then pass the BOM into our ERP system.
It all sounds good up until I looked at how our part files were structured. There is not BOM in an ipt that I have found phantom or referential. Here is my problem
It takes 1 lb of a .0625" thich steel sheet that is 6.5" wide. We stamp our product in a 200 ton press producing a finish componet.Problem 1- Part1.ipt (model of my stamping) does not have a lower level it is a component in Inventor there is no BOM that I have found.Problem 2 - Part2.iam uses part1ipt but we punch a hole in it and push material outward to create a lip so we can lap weld the next part.When I try to extrude this feature I can only cut the part I cannot add material or deform it in any way.Problem 3 - We also manufacture bent tubes. We consume 1.5 ft of part C to make part D. I cannot insert 1.5ft of a part that is 20ft long as we buy it. then we bend it. I cannot insert a 1.5ft part into an assembly and then bend it.
Major problem - even though I can change the dwg file or idw file to add a parts list Vault does not put this information in the Item master BOM.
We have a general template (excel file) for material list. Is there way to connect this template with inventor. Or alternatively change the inventor BOM list to suite our template?
View 1 Replies View RelatedI would like to have the material, color etc. as parameter so i can change it with an ilogic form.
In this video you can see what i mean:
[URL]
When I make a ilogic form i can only select parameters and iproperties.
I created a template file for the sheet material with the specified type of material, sheet thickness and the radius of bending. Placed in the Templates folder. Call the template from the menu, HED, and all settings are reset to Default? How to make a new file so that all settings are saved?
View 3 Replies View RelatedI have a user that has created a new material which is now sitting as a local style. We require this new material in the library so that everyone can use it. I tried RMB on it but the save to library functon is greyed out. This is due to the styles being read only in the project file. So I have tried to change the project file so we can add the style and then I'd change it back again, but, even though I have checked out the project file from vault, it won't allow me to edit it. What else can be locking the project file? Is there some other way I can place the new material into the style library in the project file? There are quite a few of us that use the project file since we use vault, so I'm not sure I should create a new one with the same name and save over it.
View 3 Replies View RelatedIf I need to change the material of all parts in an assembly I find it convenient to do this in the BOM. In the 'parts only' view I add the material column, change the first one and just drag it down like in Excel.
There are however some parts where the material is greyed-out (see attached image) and I cannot change them in to something else. I already traced this to parts which are present in multiple different sub-assemblies. I guess that's also the reason for the blueish/red icon instead of a normal part icon.
If I open one of the sub-assemblies the part is fine and I can change the material.
Inventor 2013
Necessary to convert list of material of the assembly (IAM) into archive pdf. (bill of Material)
View 3 Replies View RelatedI need som code to assigning a material to a part in VBA.
Dim oApp As Inventor.Application
Set oApp = ThisApplication
Dim oDoc As PartDocument
Set oDoc = oApp.ActiveDocument
Dim oPropsets As PropertySets
Set oPropsets = oDoc.PropertySets
Dim Mat As String
[code]....
but the material is not changed .....
Why Inventor rename some colors/material when migrating style library from 2012 to 2013? It's very annoying (and stupid in my opinion).
And Inventor said me "Some color/materail was renamed". Yeah good information but can you said me which color was renamed?!?
Does the developpers think about Vault when changing those color? What is the impact on the file (edited out of turn by example...).
Our customers have many colors who become differents when migrating to 2013 and it's not acceptable.
We have recently upgraded from Inventor 2011 Routed Systems to Inventor Pro 2012. We are using XP fully updated to the lastest SP and everything. We have everything configured to our preferences but there is one thing that has been driving me batty. When editing a solid part I open the Style and Standard Editor. Down near the bottom under Realistic Appearance where there should be a ball with a shiney swatch there is a yellow triangle mocking me saying Autodesk Material Library is not available, also none of the bump maps are showing up on new or migrated files whether this is a related issue I am not sure of. All of the normal and custom textures show up just fine, and all the bump textures are in their correct folder in the correct place. I have tried switching the design data folder around with no success.
View 7 Replies View RelatedI am using inventor 2012 but the material library is not loading.Then i go to the Manage> Styles Editor> and clieck on color or material it only gives me the option of defualt.
The drop down box in the top right is greyed out so i cannot change this either.
It works fine on another PC just not mine.I have downloaded the material pack from the website also.
I have also changed the hardware settings. I have tried all 3 hardware settings and it makes no differance.
Running windows 7 x64, 8 gigs of ram 3.4 quad core, 128gig SSD.
Everything is up to date.When i installed the material library download the material library was working, but when i opened a file the material library went back to how it was above.
The files i am using are from models i made in inventor 2010, but there is no problem on another PC i use.