This is the second time this has happened... While putting in the dimension on the rectangle, The dimension just doesn't appear!
But it can be changed. When this happens I just delete and reopen another part.
Why is this, and, can this be changed?
I want to creat a driven dimension that I can use as a reference dimension in another part. Is there an easy way to do this without creating a new sketch, going into a previous sketch, making a long function based on other dimensions, etc.? For instance, just like the measure tool, but it stores the measurement.
View 4 Replies View RelatedIs there any way to change the size of dimension text in sketch? My students cannot see the dimension when I demonstrate the sketch.
View 9 Replies View RelatedHow can I do this? A reference dimension was created by a circular pattern and it covers a circle I'm try to select.
View 2 Replies View RelatedSeen this recently? Using Inventor 2012 SP1 on Windows 7, 64 bit. If we go back into a previously created sketch and edit or add a dimension, upon clicking the green check mark to complete the dimension edit, the sketch exits back to the modelling environment, meaning we have to edit the sketch again to continue with other changes. Obviously no big deal if I'm only editing one dimension, but how often does that happen?
This started happening prior to SP1 being installed. We have this happening on multiple computers (all with the same hardware specs) in our office. I don't believe it to be a hardware or driver issue, but I am wondering if it is a process issue. For example, we use project geometry a lot, even projecting from other parts within an assembly (non-adaptively). We also work on SAT file models, rather than geometry initially created from Inventor itself.
Inventor 2013 Product Design Suite
Vault Professional 2013
Windows7 x64
Autodesk Inventor Certified Professional
In 2012 when in a sketch in an assembly all the stuff under "Format" is grayed out.
You cannot make a dimension driven, nor can you make a line construction or a centerline and you can't change a sketch point into a center point. Do I have some setting wrong?
I have a part.I use some Parameters of this part as linked to other parts.Once I change any parameter used as linked the other parts will follow it automatically.So I have drive and driven parts.
Now for some reason I need to change some geometry in my drive part in the way my drive dimension must be reattached to other geometry points.
I cannot delete and create the new dimension even with the same name since all my driven parts will lose this linked parameter in either way and this parameter becomes static (Reference Parameter).
I wish I can preserve the existing dimension (parameter) and reattach it to other geometry.
I am trying to apply dimension constraint for circle to add the radius dimension.
I have given the dimension location text point as input, but it doesn't take input location point to place the dimension and places the dimension at the center of circle. Please see the attached snap "CircleWithRadius.png".
Here is the sample
//===============================
CComPtr<Point2d> point2D;
TransientGeometry::CreatePoint2d(5, 5, &point2D);
CComPtr<SketchPoint> sketchPoint = SketchPoints::MethodAdd(point2D, FALSE);
CComPtr<SketchCircle> sketchCircle = SketchCircles::MethodAddByCenterRadius(sketchPoint, 3);
[Code] ........
Why the circle entity always place the radius at the center of circle?
I have created a SketchLine entity and trying to add aligned dimension by calling DimensionConstraints::AddTwoPointDistance(). It adds the dimension with inside arrowhead (see attached CurrentWorking.jpg), however, it would be nice if the dimension is added with outside arrowhead (see attached Expected.jpg).
if there is any API to toggle the dimension arrowhead accordingly.
How does one (in sketch mode) dimension from the quad of a circle instead of the center? Been dealing with it for a long time, no I am fed up and want to dimension from the quad.
View 6 Replies View RelatedI am having trouble changing the dimension text size of any 2d or 3d sketch..
the default has changed for some reason (i might have accidentally changed it while looking for something the other day) but i need to know how to change it back.. I can't do anything without a dimension getting in the way!
This is the first I've noticed this, but a sketch in an assembly does not allow to show the dimensions as an expression? In a .ipt sketch you can right click and the pop-up menu has an option to show the dimensions in different forms. I do not get this in an assembly sketch.
I do not know if this is me or not. It's just curious that it does not do that.
I need to disable the "Set sketch scale by the first dimension" feature.
The feature is nice under normal circumstances, but in my case i need to insert a dxf sketch and then draw around it in inventor. When i start to dimensioning the sketch then it scales the inserted part.
That aint so good.
How do I change the dimension size in sketch mode?
View 4 Replies View RelatedOctagon inside a circle... The circle cannot be dimensioned off the octagon?
I need it to have, say .25" clearance and I mean I can just make the circle the right size... but Inventor/I really should be able to do something this simple...
A circle inside a circle, same center point, you can click both and get the distance between the two?
(R-click and set circle to Radius does nothing, it still wants to dimension it from the center point)
I have a VB program that auto updates the size of a door and frame assembly, and in turn, updates the shop drawings to reflect this change. I have a view on my shop drawing that I have drawn a sketch in. I start the sketch, add my dimensions, and I use 'Project Geometry' to project the edges of the actual part around the sketch to constrain my sketch and keep it in place. The problem is, as the program runs, and the door/frame changes height, the sketch loses it's dimensional references to the projected geometry. When I go back and reopen the drawing after running the program, all the dimensions that went to the projected geometry are gone.
Is there another way to anchor a sketch to a drawing view part instead of dimensioning to projected geometries? This doesn't seem to be working, and I've tried it every which way I can think of. Oddly enough, I have another sketch in a different view that is set up the same way, and it never misses a beat.
Why the heck does Inventor arbitrarily orient sketches as it sees fit? I often create my first sketch on the right (YZ) plane and Inventor, stupidly turns the sketch where "RIGHT" in the viewcube reads from top to bottom.
I know all the things to do to AFTER this happens, but it shouldn't happen in the first place. If I turn my sketch so that up is up, like it should be, I then have to remember that vertical is horizontal, which is now vertical. I can't change the sketch coordinate system. It's the first sketch and there is nothing to align it to.
How to prevent the above example from occurring in the first place.
This, and the fact that I can't dimension to any existing vertices or edges without projecting them first, really make me hate using Inventor sometimes. To me, these are huge problems, neither of which Solidworks has. At worst, both of these behaviors should be configurable.
Why is dimension visibility grayed out in the sketch context menu shown in the attached image?
View 3 Replies View RelatedI cannot select origin to constrain sketch with dimension to origin?
I selected Sketch,
expanded origin,
selected mywork plan (xy)
drew rectangle,
input dims,
right click for marking menu,
selected dimensions,
Origin is yellow,
cannot select it and then edge of rect to set dim that will center sketch on origin? Just like the videos show, but cannot select origin>
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
View 2 Replies View RelatedHow do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
I was trying to query some sketch points data from a profile Path using code as below. However the program stopped without telling the reason.
Code below:
i = 0;
foreach (ProfileEntity oSourceProfileEntity in oProfilePath) { switch (oProfilePath[i].SketchEntity.Type) { case ObjectTypeEnum.kSketchArcObject: { SketchArc srcSkArc = default(SketchArc); srcSkArc = (SketchArc) oSourceProfileEntity.SketchEntity; // error points[i] = srcSkArc.StartSketchPoint.Geometry; break; } default: { SketchLine srcSkLine = default(SketchLine); srcSkLine =(SketchLine) oProfilePath[i].SketchEntity; // error points[i] = srcSkLine.StartSketchPoint.Geometry; break; } } i++; }
First we imported an ".igs" file to inventor, which produced "wires". Then by promoting the wires it produced a 3-d sketch.
The model is in one plane and 2-D, and we are trying to use Ansys 2-D analysis, but in-order to do so it needs to be in a 2-D sketch.
The model is too large to be redrawn on a 2-D plane, how to convert it to a 2-D sketch
want to change sketch 2013 into the sketch of 2010
View 1 Replies View RelatedWhen I edit certain sketched some other sketches disappear. see attached.
This is causing modelling to slow down as I can not project lines from the sketch that has disappeared.
After I create a adaptive part from projected sketch. How to modify the sketch? Please see the part attached.
View 6 Replies View Relatedwhat is the difference between a sketch and a planar sketch?
View 2 Replies View RelatedI'm having trouble with constaints, I'd like to constrain my sketch to a point in another sketch on a different plane. Is this posible in Inventor? If so how? If Inventor works differently how would you get a points in one sketch to be linked to points another?
View 2 Replies View RelatedI have one problem in ilogic "How to convert the normal dimension to driven dimension through ilogic"
View 4 Replies View Relatedhow to make a radius dimension a diameter dimension? I have Inventor Profession 2013.
View 1 Replies View RelatedIs there a way to override a dimension and have it shown as a GD&T Basic dimension. I can override a dimension with the text option but not with a box around the letter. It sounds strange to do this but the letter represents a dimension in a chart format that are Basic dimensions.
View 9 Replies View Related