In Inventor R11, SP2 why :
(1) Why can't you use the Sweep command with a 3D sketch?
(2) Why can't you draw circles in the 3D sketch environment? What do you do if you need to sweep a cut with a circular profile along a 3D sketch line?
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
View 2 Replies View RelatedHow do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
I was trying to query some sketch points data from a profile Path using code as below. However the program stopped without telling the reason.
Code below:
i = 0;
foreach (ProfileEntity oSourceProfileEntity in oProfilePath) { switch (oProfilePath[i].SketchEntity.Type) { case ObjectTypeEnum.kSketchArcObject: { SketchArc srcSkArc = default(SketchArc); srcSkArc = (SketchArc) oSourceProfileEntity.SketchEntity; // error points[i] = srcSkArc.StartSketchPoint.Geometry; break; } default: { SketchLine srcSkLine = default(SketchLine); srcSkLine =(SketchLine) oProfilePath[i].SketchEntity; // error points[i] = srcSkLine.StartSketchPoint.Geometry; break; } } i++; }
First we imported an ".igs" file to inventor, which produced "wires". Then by promoting the wires it produced a 3-d sketch.
The model is in one plane and 2-D, and we are trying to use Ansys 2-D analysis, but in-order to do so it needs to be in a 2-D sketch.
The model is too large to be redrawn on a 2-D plane, how to convert it to a 2-D sketch
want to change sketch 2013 into the sketch of 2010
View 1 Replies View RelatedWhen I edit certain sketched some other sketches disappear. see attached.
This is causing modelling to slow down as I can not project lines from the sketch that has disappeared.
After I create a adaptive part from projected sketch. How to modify the sketch? Please see the part attached.
View 6 Replies View Relatedwhat is the difference between a sketch and a planar sketch?
View 2 Replies View RelatedI'm having trouble with constaints, I'd like to constrain my sketch to a point in another sketch on a different plane. Is this posible in Inventor? If so how? If Inventor works differently how would you get a points in one sketch to be linked to points another?
View 2 Replies View RelatedHow were the various different colour "sweeps" () done? I think that they're rediculously cool but I have very little idea of how to do them this well.
View 17 Replies View RelatedI am trying to create a cornice using a wall sweep. I created the profile I need but when I load the profile and try to add the sweep to the wall Revit shuts down completely.
View 1 Replies View RelatedWhat's the best way to create the attached: EQ ashlar panels, and wall sweeps with joints?
View 8 Replies View RelatedI'm, trying to update my wall profile so that all of my interior walls have baseboard/molding on them. I've been successful in creating a wall profile with molding, but only on one side. Looks like this in plan view. (Molding is highlighted and only on one side.)So, I first try to update my wall profile like this:
And I either duplicate, or add another sweep to the wall, and make that "Exterior" as to be on the "other" side of the wall.However, after pressing "OK" and "OK" at the wall profile editing box, I get the following error box:
When I click on "Show", I'm shown nothing. When I click on "Enjoin Elements", this same box comes up no matter how many times I click on the "Enjoin Elements" button.
Having problems adding molding to both sides of their interior walls? Am I going about this the right way? Tried to smallify the actual .rvt file, but I can't get it down to an acceptable size for posting here.
Just installed inventor on a new PC. When I go to sketch a line it appears to be drawn but nothing is being created.
View 4 Replies View RelatedIs it possible to offset this 3D sketch1, it must still follow the curvature.
View 9 Replies View RelatedInventor 2011 will not offset polygon in sketch mode. I get "Method not supported for transient meta" error message.
View 9 Replies View Relatedis it possible to create 3D sketch from text?
I need it for engraving as a toolpath and for drawings.
Emboss tool is more suitable for styling and visualisation.
Attached sample from Pro-E:
I need to print an initial 2d sketch (without any 3d work done on it).
Printing this in sketch mode seems to output a screen capture, i.e. some lines appear wriggly and not as precise as an ordinary plot of an idw or dwg file.
A sketch w/o any 3d work will not be accepted as an idw file, thus I am not able to use all the formatting (tblocks, fonts, dimstyles, etc.) options available to idw files.
Is there a way of printing a 2d sketch (w/o any 3d work) as an idw file?
I've managed to hack together some code to draw a rectangle and dimension it. Now I want to constrain it to the origin. I figure either using two dimensions from a top/side to the origin and setting the dimension as half of the other respective dimension would work. Or constraining the center point of a top/side line to be vertical/horizontal to the origin.
The problem I'm having is I do not know how to reference the origin. So until I figure out how to reference the origin point I can't use either method.
Public Sub DrawSketchLine() ' Check to make sure a sketch is open. If Not TypeOf ThisApplication.ActiveEditObject Is PlanarSketch Then MsgBox "A sketch must be active." Exit Sub End If ' Set a reference to the active sketch. Dim oSketch As PlanarSketch Set oSketch = ThisApplication.ActiveEditObject ' Set a reference to the transient geometry collection. Dim oTransGeom As TransientGeometry Set oTransGeom = ThisApplication.TransientGeometry Dim oUOM As UnitsOfMeasure Set oUOM =
[Code].......
Is there a way to update a symbol of one type, without the changes being applied to all symbols of that type in the drawing?
Example: If I have three Flag Note symbol's in my drawing from the same sketch symbol and the text reads 1, is there a way that I can change the text to read 2 in one of them without the other two flag notes updating as well?
IV 2012 Pro-Suite / VP 2011
Windows Vista Enterprise - 64 Bit
Precision Workstation T7500
Intel (R) Xeon (R) CPU - E5504 @ 2.00 GHz (8 CPUs)
12284 Mb Ram
Dual Quadro FX 5800
I keep getting this error adding a sketch to any view in an IDW... What might be causing this error?
View 1 Replies View RelatedI want to make some points in 3D sketch base on the Coordinate System that I defined (UCS).Is there any solution to make these points in 3D sketch just by inputing their coordinates in my UCS?
Example: the new UCS origin has (x,y,z) coordinates from the origin.and one of the points has the coordinates of (x',y',z') from the UCS.
So from the origin it has the coordinates of (x+x',y+y',z+z').Is it possible to just use (x',y',z') from UCS directly to get my point?
I'm trying to put some text into a sketch I have. My issue is the text is coming out sideways. I want the text horizontally.
I tried to use the rotate tool but I can't find a center point in the text box.
I am working on iLogic models and have a sketch feature in a part that is used as a referance for a caulk bead. The sketch is in an IPT and is a stand alone feature. I am trying to have this sketch feature be visible in and IDW file of the product I am developing but cannot seem to find a solution. Is this even possible and if so what am I doing wrong?
I am doing it this way because the caulk bead spans the entire height of the part which can change via different custom parameters, therefore the caulk bead needs to be able to change with the part while not losing its sketch references.
I'm trying to make a .dxf or .dwg from our company logo to use it in many parts and assemblies. I also would like to be able to resize it. When I export the sketch from the attached model, and use it in a new part, it says there's open loops and other problems. These do not occur in the original part when using sketch doctor.
What's wrong with the sketch? Is there easier ways to emboss the logo on multiple parts?
When importing Acad files is it possible to imprort without having to fix the sketch in inventor? Meaning, if the Acad drawing was drawn so all the lines attach to another ("closed loop") why is it when I import and select all the layers or (no layers) that i can not extrude the sketch in inventor without always having to fix.
-Redundant points
-Missing Coincident contraints
-Overlapping curves
-open loops
-self intersecting loops
Before importing the autocad file, what needs to be done to the autocad drawing before importing for a flawless sketch so i can just extrude it in inventor?
I know my subject is somewhat mis-named, because I gather that you cannot really extrude from a 3D sketch, however I am looking for a way to accomplish what extruding a cut from a 3D sketch would accomplish.
The problem is this: I have a simple 2D sketch that I've projected onto a curved surface (imagine a square projected onto the outside of a hollow cylinder). Now that I have a 3D sketch on the surface of the cylinder, I want to use that sketch as a "cookie cutter" through one wall of the cylinder.
If I were to simply extrude the cut from the 2D sketch, the "cookie" is wider at the edges than at the center. I want the cut to be perpendicular to the projected 3D sketch at all points.
I've attached a simple example that illustrates my problem.
Why do we not have the "=" (equals) constraint option in 3D Sketch mode? It seems like a very basic need for a constraint. Is there a reason why one should NOT want to have an "equal" constraint in a 3D Sketch?
View 3 Replies View RelatedWhy is it when I select the Top (XZ Plane) does the sketch orient itself so TOP is read upside down? Subsequent Sketches on a TOP face yields expected results.
And it is also true that it if I select Right (XY) the sketch orients itself so RIGHT reads top to bottom? and if I rotate the cube orientation so TOP is truly on top, the Constrain Axis' are off by 90º? yet if I subsequently select the RIGHT face for a sketch, it yields expected results (RIGHT reads from left to right).
This cannot be the way it is supposed to be. it although has been this way for may versions.
M6700, Nvidia K3000M, 32GB, 512 SSD
Win 7 Ultimate 64
Inventor 2014
I sometimes edit parts in assemblies. When I turn sketch visibility on or off it does not stay the way I left it. I should be able to edit a part in part view or assembly and the view setting off or on should be how it was last saved. If I saved an ipt with the vision it should be on in any & all assemblies it lives in but its not. I have noticed the difference in new version 2012 - 2011 was no problem.
View 1 Replies View Related