AutoCAD Dynamic Blocks :: Schematic Block Creation

Oct 12, 2013

I need to create a block for all our schematic work. Right now were are doing the schematic part in Visio, but like to move that part to auto cad if it is possible.

I wonder if this is possible to create though. A dynamic block that you can drag out to expose more terminals To be able to label the terminals individually. For each wire terminal to provide a snap function so lines can easily snap to them. Be able to label each wire that gets connected individually.

Be able to add a heading to each block for make and model number. Not sure if acad can actually do all this with dynamic blocks. I attached an image from Visio as well.

View 2 Replies


ADVERTISEMENT

AutoCAD .NET :: Dynamic Block - Programmatic Creation

Dec 25, 2013

I am currently looking into the creation of dynamic blocks. I've have not been able to get a hold of the objects that make a block dynamic (parameters, grips, actions)

There is a table with records. One of those records is the Model Space (drawing area). All drawing objects are recorded here. All layouts have the same hierarchical level as the model space. All Blocks in the document also have the same hierarchical level as the model space.

This would be a representation of the above.

-Table
-Model Space
-polyline
-text
-etc.

-Paper Space
-polyline
-line
-MyBlock
-Polyline
-Text
-Alignment parameter
-Alignment grip

So, with this in mind I've been trying to study the dynamic blocks so I can create them programatically but when I cycle through the ObjectID's inside my block record (in this case MyBlock) it would only show the Id's for the Polyline and the text and not the other two.

It seems they are recorded elsewhere.

I want to access the object and figure out later how it relates to the other objects and make it dynamic.

View 1 Replies View Related

AutoCad 2D :: Dynamic Block Creation - Height To Length Ratio

May 18, 2013

I am using AutoCad Architecture 2011 and I am in the midst of creating a simple line drawing of a bifold door. I have two lines. Each at opposing 45 degree angles. The objective is to have each line segment equal to half the distance measured between two points. For example; if the door opening is 2' wide each line of the bifold doors should be 1' in length if measured diagonally. The result would be a line, if stretched out, would equal 2'.

I've created a block that can stretch and rotate but I just can't figure out the height to length ratio thing.

View 8 Replies View Related

AutoCAD Dynamic Blocks :: Link Dynamic Block Custom Rotation Action

Mar 22, 2013

So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it.  However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle.  Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.

This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Moving Properties Table Grip In Dynamic Block

Jun 13, 2013

I have a dynamic block, that represents a stirrup.

I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.

The problem is that I can't make this grip moveable )

See the attachement with the block

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Flipping Dynamic Block With Multiple Items Not Visible

Jul 25, 2012

new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way.  I now want to add an overall flip to the entire block and have not been able to find set this.  I would prefer to use the same label and go from there.  I have included the block to show what I mean.  It is only working on the single visible item at the one time.  I know this has to be possible just let me know what I am doing wrong.  I am running AutoCad LT 2013 

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Create A Dynamic Block For Glass Panel In Balustrade

Feb 28, 2012

I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.

I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right  hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Insertion Point Of Attribute Changing Within Dynamic Block

Nov 21, 2011

I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.

But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Pass Attribute Values To Dynamic Block Parameters?

Dec 4, 2013

I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.

View 1 Replies View Related

AutoCAD Dynamic Blocks :: How To Disable The Dialog Box Shown When Open A Dynamic Block

Nov 7, 2011

I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.

Is there a way to disable that dialog and open the files as normal dwgs?

A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...

View 4 Replies View Related

AutoCAD Dynamic Blocks :: Make Dynamic Block Of Column Radiator

Mar 26, 2012

I'm trying to make a dynamic block of a column radiator.

It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).

My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.

View 4 Replies View Related

AutoCad :: Insert Dynamic Block From File With Multiple Dynamic Blocks

Jul 16, 2010

I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".

For that i tried creating a new command "INSERT_M12" that has the following script :

^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"

Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Join Two Dynamic Block To One Common Action?

Sep 18, 2013

I'm working on a drawing and I want an action to work on two diffrent dynamic blocks. 

In my case, I wish to have two blocks that I can rotate by one rotation grip.

How do I manage to work this out?

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Stretch Dynamic Block Grip Points

Feb 4, 2011

I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.

I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.

But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.

View 9 Replies View Related

AutoCAD Dynamic Blocks :: How To Create WAVE Dynamic Block

Mar 1, 2013

I would like to create a "wave" dynamic block, see below...

It is made from wipeout.

Is it chance to make a similar?

If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Scaling Objects In Dynamic Block

Jun 27, 2013

Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.

I tried adding position point and link, etc....I run out options and don't know how to fix this.

LT 2012 user

AutoCAD LT 2012
Windows 7 - 64 bit

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Grip Point Dynamic Block

Nov 15, 2012

I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).

View 9 Replies View Related

AutoCAD Dynamic Blocks :: How To Keep An Object Centered On A Dynamic Block

May 29, 2013

I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered

I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.

View 6 Replies View Related

AutoCAD Dynamic Blocks :: Create Dynamic Block With Dimension

Jan 4, 2014

I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.

LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi

Then, I use command DAL; I can select dimension want use.

View 8 Replies View Related

AutoCAD Dynamic Blocks :: Stretch A Hatch In Dynamic Block?

Jul 4, 2013

How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Keep Item Centered In Dynamic Block?

Mar 5, 2012

I have an X centered as my insertion point.

When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.

how to get the X to be centered in the box when it is enlarged to a double or triple size?

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Mirrored Rotation Dynamic Block

Jun 14, 2012

Is it possible to mirror a rotation within a dynamic block?

See the attached drawing.  I am trying to have two rotations within a dynamic block, but only one grip.  When the grip is rotated one half of the block rotates while the other half rotates in reverse.  The resulting action would be much like the wings of a butterfly.

I have tried many different combinations of parameters, actions and constraints with no luck.  The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?

View 7 Replies View Related

AutoCAD Dynamic Blocks :: Dynamic Block Linear Array?

May 5, 2012

I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.

View 5 Replies View Related

AutoCAD Dynamic Blocks :: Selecting A Edited Dynamic Block?

Mar 28, 2011

I have the attached file as a dynamic block.

Last week I opened the drawing and added some visibilty states etc. to the block.

Now when I open the block or insert it into another drawing for whatever reason the cursor or crosshairs stop at the edge of the block. And if you move towards the middle of the block where there isn't any lines etc. the cursor will move to that point until you hit another line then it will stop moving again.

I've been reading some other posts for different dynamic block topics/issues and read that everyone has problems when you get to higher numbers of visibility states, but when I edited last week I only added 7 states. Is that enough to make this happen? It sounds like everyone else that is having problems has far fewer visibility states than on the attached drawing. 

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Moving Dynamic Block With Attributes

Dec 19, 2011

I made a dynamic block with attributes. The block was to be moved using Linear parameter + move action, and then a lookup parameter and action.

The block moves as it is suppose to but the attributes are left behind. How can I get the attributes to move with the dynamic block?

The attribute properties are:

Verify = Yes.

Lock position: Yes or No don't seem to make a difference.

Is this a bug in AutoCAD or is there a solution to this?

View 3 Replies View Related

AutoCAD Dynamic Blocks :: How To Create A Dynamic Block That Changes In Scale

Jul 27, 2011

I am looking to create a dynamic block that changes in scale, ex. If I have two (2) viewports in paper space, one 1/4"=1'-0" the other 1/8"=1'-0" I want my blocks to appear to be the same size in paper space.

Also, I would like my blocks to change attributes/features ex. If I have a "light switch block" I would like to have the option of switching the block from a 3-way switch, 4-way switch etc.

View 4 Replies View Related

AutoCAD .NET :: Dynamic Block Creation With Selection Sets Of Drawing Objects

Mar 19, 2012

It's possible to create a dynamic block programatically? I want to create a command that captures different selection sets of drawing objects and assign them to different Visibility States of a new block deffinition, on run time.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: How To Get Blocks To Have Images Associated With Actual Block Name

Apr 29, 2013

I am using AutoCAD 2013 on Windows 7 platform

95% of the blocks on the palettes have the images associated, and named, per the block name.

I have 48 blocks that the images are named like this "Block tool_F2149212-4649-41F5-95E6-4A978EC376F5_2".

I have tried resaving the blocks and recreating the blocks to no avail.

How to get these few blocks to have images that are associated with the actual block name and not the generic "block_too" name?

View 4 Replies View Related

AutoCAD Dynamic Blocks :: Piping Dynamic Block

Oct 6, 2011

The block is a piping with various links that back together and they should stay behind each other, they are not go over each other otherwise the spacing is not good after data extraction.

The distance between not less than 100 mm and the total length should not exceed 5000mm are. Furthermore, they are relatively movable from each other.

I've been working with linear parameters and constraints, but that's not good as far as I know I can not apply visibility  later with links that point to the other side.

View 1 Replies View Related

AutoCAD Dynamic Blocks :: How To Create Y Dynamic Block

Feb 28, 2013

I would like to create an "Y" dynamic block, see bellow.

The hole length and the "cross" point will be variable, between the two sticks will be 90 deg, and it will be FIX.

I would like if I change the "variable 2" distance the two sticks follow the cross point, and the top of the sticks stay in the same level, but between the sticks the 90 deg stay!

View 9 Replies View Related

AutoCad :: Dynamic Piping Blocks - Inserting And Linking A Flange Block To Pipe Block?

May 21, 2013

I have created d/blocks for my different pipe sizes i.e one block with a dropdown to select the different sizes and have done the same for my flanges. now how do I link / insert the flange d/block to the piping block so that I can export the information into a material list later on.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved