I'm looking for solution for this error: Mask '0' NOT added to corridor surface 'Corridor - (1) - (1)' as boundary due to crossing polygon.
View 6 RepliesI added three feature lines to my surface as breaklines. But the triangles still cross them. Triangles shouldn't be crossing breaklines.
View 2 Replies View RelatedI have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies View RelatedWhen I create a corridor surface I usually create a suface boundary automatically by daylight.Half the time this works fine, half the time it doesn't work at all. If I view the corridor in 3d view it looks fine.
I tried to create a shrinkwrap polyline to use as a boundary but when I picked the corridor in the shrinkwrap command
it locked up my computer. These are just simple corridors with no intersections. Why the automatic boundary only works intermitently? Is there a better/easier way to create the surface boundary?
Cannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?
View 3 Replies View RelatedI have problem with corridor surface boundary , in curve boundary line is jumping on daylight fill , but i have created surface on wearing layer ,also when i am adding boundary there is only 3 types of adding , corridor extends , polygon and interactively , photo attached.
I am using Civil 3D 2014
I used a 2d polyline to create a surface boundary for a surface created. The polyline is a closed loop. For the boundary type it is outer, unchecked Non-destructive breakline, and mid-ordinate distance = 1.
My problem is that when I do this I only get a small portion of the surface to show up within my surface boundary. If I don't have a surface boundary the entire drawing surface shows up no problem.
The purple polyline is my boundary and the light blue is the surface created within the boundary.
We are starting a new job, and looking how to setup our drawings. We have a long corridor that we are upgrading, and along this corridor, we have various water course passing through. We are replacing the existing culverts. They are large circular culverts. How do we show the culverts on our model? Do I create a short pipe network for each culvert crossing? And also, how do I daylight to the outside of the culvert as the corridor crosses over it?
View 4 Replies View RelatedIs there a way to show a corridor assembly in a crossing profile in c3d 2012? I have a underground duct bank that I have modeled using a simple corridor. Now I want to have the duct bank assembly show up in another profile that crosses the ductbank corridror. I can't really create a surface fom the corridor since the duct bank a closed polygon. BTW, The subassembly for the duct bank was created from a polygon, if that is any useful info.
View 6 Replies View RelatedMy corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
I've set the corridor's surfaces to use the corridor boundariy & the datum's overhang correction to top links & bottom links, but for some reason it doesn't respect the corridor's boundary.
View 2 Replies View Relatedall of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies View RelatedMy problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies View RelatedI am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
When trying to select entities with a window or crossing polygon (and hitting enter) there are no grips showing to indicate that the selection has been completed even though the entities seem to be highlighted. Syntax: select, enter, wp, enter (draw polygon), enter.
I am a part time user of this wonderful program and only recently moved to 2010 and yet I cannot figure out what I am doing wrong. I have Googled and looked in my texts and still am having difficulty (also attempted to search FAQ on this site but the link malfunctioned).
I have survey data of the inside floor of a pond ( the pond has a flat floor ). The surface made from the survey data needs to extend to the outline of the pond instead of the outline of the survey points.
I tried the smooth surface method of kriging with a grid base and I sellected the outline of the pond for the output region and that worked somewhat but there are still gaps between the boarder and the surface.
I have alignments that go in and out of a surface boundary (this is because I have a surface that represents the bottom of pavement.) I want to show the surface profile with the gaps in the profile view (where there is no surface. However in the profile view the gaps are sometimes connected with a straight line instead of being blank.
How can I have a surface profile represent the bottom of pavement properly? (An alignment that is not fully withing the surface boundary.) I know I could add the profile multiple time with different start/end stations But, I don't want that, I want it to be dynamic, as the alignment will change.
The odd shapes are outside the daylight line. They follow a straight-line around the daylight limits (see third attached file), apparently triangulating unwanted areas. I've used a corridor shrink wrap for the surface boundary.
What is the best bet? I'd rather not draw a polygon along the daylight line and use it as a surface boundary, since it could change. Setting a max triangle length in the surface does not seem to provide a desired result.
I have problems applying an Outer boundary to eliminate a small area within a big surface (and a few Hide boundaries within that Outer boundary): Civil 3D somehow creates extra triangles within my surface (that don't really make sense to me). I am applying the boundaries as non-destructive boundaries as I need the surface to extend all the way to my applied boundaries. The surface needs to be untouched (except applying a few Outer and Hide boundaries) as it is design data.
View 4 Replies View RelatedI need to adjust a surface boundary. I need to remove a corrupted area in my surface. I do not need it. Is there any way to drag a boundary so I can exclude some of my contour area? Is there a command under settings on tool space that I may have overlooked? This surface was furnished by a client so I do not want to rebuild or alter except to exclude some contours.
View 1 Replies View RelatedI am using a breakline to establish contours around the foundation of a building. I've done this in the past with no problems. Now I'm getting an Event Viewer, Error message saying that the breakline wasn't added to the surface because it crossed a point or crossed another breakline. In one case there wasn't another breakline in the drawing.
I've used 3d polylines & others to establish the breaklines.
I am getting this error when I am trying to create a surface from my corridor. Instead of just defining a surface along my corridor it is trying to connect all contours lines between different parts of the corridor
When creating the surface I define 2 surfaces, one with overhang correction as top links with links data set as top, and a second with overhang correction as bottom links with links data defined as datum. I have then defined the boudaries using add automatically-daylight. I have followed this procedure for 5 previous corridors with no issues (ie the surface matches the corridor) so is there anyway I could have done something different.
what is the trick for holding triangulation within a surface boundary? I recall a setting somewhere but can't seem to find it... attached graphic, would like to hold the surface triangulation within the arcs which are in the surface definition as boundary
View 5 Replies View RelatedI need to convert my surface boundary to a polyline so I can use it to clip another surface. Is there a simpler way than tracing it with the polyline command?
View 3 Replies View RelatedI have a surface that I created by joining to surfaces, and now I want to reduce my boundary, how can I edit it?
windows 7, intel I7, 8 MB RAM, civil3d 2013.
I use Civil 3D 2011. I have created a surface from a point group. Now i want to extend the surface to an outer boundary. To do so, i do the following steps:
- Select the surface and Extract the border object.
- Create feature line from the extracted border polyline
- offset this feature line (featureoffset) to outside specifying a offset distance and specifying the elevation difference as 0.
- Add this offseted new featureline as the boundary in the definition of the surface
- Rebuild the surface
Now when i am selecting the surface, I see that the featureline is not a part of the surface and I do not find the contours and the TIN extending to this new boundary. Also I still find the old border in the surface.
After adding 9 or so breaklines, the display of my surface (e.g. contours) disappears when I add the next breakline. Based on the surface elevation shown at the pointer location, the breakline seems to have been added and the surface rebuilt.
View 3 Replies View RelatedI'm creating a corridor to widen a road on the left and right sides. I am using OverlayWidenMatchSlope, with various other subassemblies. In places it daylights, in places there's a cut wall modeled from generic links. I am trying to create a good boundary for the corridor surfaces but I'm puzzled by one thing. The OWMS subassembly has a P2 code, but the corridor will not generate a featureline connecting the P2 codes..
I will try adding another baseline, and a new subassembly that will just use a generic link to target the sawcut line (the insert point for OWMS). That should give me a featureline I can use for a surface boundary. Is there a way to generate that featureline from the inside edge (the insert point) of the OWMS subassembly?
Win 7 64-bit, Intel i7 920,12 GB
Win 7E 64-bit, Intel i7, 12 GB
C3D 2012
I can only change the layer color.
But I can't change the cross simbol, its drwaing scale.
Also cant view the point number,....
Maybe I cant view or set these properties when points were added using "Point Files" option.??
Civil 3D (2013)
I know that there is a limitation on the numbers of points added to a surface from a point cloud. But I'm curious how Civil 3D determines which points to exclude from the surface. Is there a special alorithm/criteria the software uses?
View 1 Replies View RelatedWhen i try to create a material list, i don't see my corridor surface - just the EG surface appear in the list.
View 2 Replies View Related