In the surface styles dialog under analysis you can edit elevations, colors, etc. EXCEPT for user contours. What I would like to do is edit these for user contours, then when I created it there would be a default of sorts.
is there any way to set a default for user contours in the style?
I have defined 3 user-defined contours for various elevations in my pond. I would like to disply them differently from one another, so I set their display styles in the analysis window where I created them. Unfortunately, the are only displayed per the settings in the surface style which is 1 - not what I want and 2 - all identitical. I have tried various settings in the surface style, but the contours will not display the way I have selected in the analysis window.
C3D 2011 w/ latest updates
I know 2013 are more exposed and the .net can extract contours. However using 2012 at the moment. so my plan is using .net to add the user contours and then use com object to extract.
so far i can get the surface object and assign to two different surface variable one is .net and one is com. I am looking at the surface analysis object and can't figure out how to add contours at user elevation. it is also read only in the surface object. but i find this:
SetContourData
(analysisData()
which is obvious not read only. so any sample code of the procedure of assign user contours?
trying to create contours from an exiting survey file. I am new to Civil 3d 2012. What I need to accomplish is create a 3d topo from the points with contours and then create a 3d model of the area.
View 9 Replies View RelatedI have a existing ground surface drefed into a model and am trying to get a user defined contour at a set elevation but nothing appears. I have userdefined layer on in the surface style and other ideas why it will not appear?
[URL] ......
How do you apply certain contour label styles to certain surface styles (i.e. When I have an existing surface i want the default contour labels to be an "existing contour" style). Right now the default is a "finished contour" label style for all surfaces.
View 4 Replies View Relatedusing Civil 3d 2009
I am editing a feature line which is a driveway. I set the feature line to have a constant slope from one end to the other. I had to move the line and when I did the contours went away. I tried to just add grading to the feature line and it when through the steps I always take and acts like its there but I dont see it. The contours are set to 1' and 5' contours w/ design. The feature line that is added when creating a grading from the original feature line (that shows the base of the slope where the contours fit between or in other words it is the feature line that follows the existing/natural ground) is also gone.
Also on another feature line all I did was go into elevation editor and change an elevation and the contours dissapeared.
I have a set of styles created in 2010, the company I currently work for needs to have new styles added and I would like to use some of the styles I created to make my life a bit simpler in this process. I have created an Overall.dwt file using the current styles the company i work for has and I have imported my styles into this dwt. As im renaming these styles for my new company I noticed under the general tab for text style and block style I have text and block styles with my old companies name but i cant seem to find where the blocks or text style is being pulled from so i can edit it with a new name. So my question is where are these styles being saved so i can edit them
View 3 Replies View RelatedSo I noticed that my data reffed pipes were reverting back to their default styles in my production drawings. This wasn't a problem with SP1. I made a support call to our reseller and they mentioned that the only work around was to completely uninstall Civil3d, then reinstall back to SP1. He mentioned that he was passing the information on to Autodesk and he would let me know if they had a fix. Naturally that kind of timing or solution doesn't really work for me. This problem will effect any drawing I have that has pipes in it.
I want to know what you have done to work around this? Is there a better solution than uninstalling Civil3d?
When you use the Import Survey Data wizard it automatically creates a point group that goes to the top of the list. This used to be created with a standard point style and description, but something has changed and I'm getting a different symbol and label that I definitely don't want as the default. I would think that this would be controled by the CreatePointGroup settings, but that isn't working for me. I can't find any other settings that would override or control this.
(running C3D 2012 sp4, Win7 64bit, 8GB)
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
When opening one custom Content Center iPart from Inventor I get an Styles Conflict error for some Lights, Materials and Sheet Metal rules.
The Library is created in Inventor 2010 and migrated to 2012. All templates an Design Data are migrated as well. How are these styles are updated in a certain Part?
See the image
i'm exporting a surface from 2013 to be used in 2010 for presentation. works great but the contour interval is not the same as the surface i'm exporting. working in 5/25 contours...xml import comes in with 2/10 contours. looked for a setting but can't seem to find.
View 2 Replies View RelatedI'm drawing a topo and trying to figure out a way to manually smooth out my contours. I'm not talking about the little jagged edges that you can remove if you use the smooth surface option under surface properties but the big ugly looking jumps you see when contouring a relatively flat lot. In the ancient version of AutoCAD my company used the contours came in almost like splines and you could move the vertices around to make them look good. I know you can go in and delete some TIN lines and edit point elevations but that is very time consuming and I'm hoping there is a quicker way.
I know I can extract them into polylines but there are too many little segments to be useful. I've seen the SIMPLIFY SURFACE option and while that takes away some of the roughness it creates some as well. Is there some better option than extracting and then drawing a spline between the parts I want to smooth out? These contours don't need to be 100% accurate, I just need them to look simple, like if someone was drawing them by hand.
I have added contours to my surface (the blue lines). For some reason the surface generated contour (the orange line) is jumping across the contours I've added.
View 8 Replies View RelatedMy TIN surface either did not generate contours or did not display them on my drawing. I created and tried surface styles of many contour intervals(from 0.5' and 4' to 2' and 10') without success. I made sure my contour layers on both the Style Dialog box Display Tab and Layer Properties Manager were turned on, still no success.
View 6 Replies View RelatedI'm having problems contouring in C3D 2014.
I'm using the command PL - polyline to create my break lines (Centerlines, top and bottom of curb)?.
In this particular drawing the first point I click on is carrying the elevation throughout the entire length and yielding bad contours.
Essentially the bottom of curb on each side of the street should be the same elevation with a crown at the centerline.
Instead the elevations are about five feet different because the beginning point is around the corne at a point of tangency on a hill.
This has not happened in any other drawings and I've done them the same way.
I redid the breaklines with the 3DPOLY command and aside from a few minor edits the surface came out OK.
I've been reading about 3DPOLY command but have not found out too much about what the actual difference is between 3DPOLY and PL commands.
Seems like 3DPOLY is the way to go.
I do not have too much experience with C3D 2014 and am making a huge jump from 2004 LDD. How to build 3D surfaces/contouring.
When I generating contour(surface) using Civil 3D it gives very complicated contours.Some times those contours cuts each other and have very strange shape.
I used to use SURFER software to generate contours.It gives simple contours.But I like to use Civil 3D because.
I attached SURFER contours and Civil 3D contours. I also attached AutoCAD file those who using older versing of Civil 3D.
I know how to smooth contours in Civil 3D but it does not solve my problem. You may say "You should use commands like swap edge,delete line .
Can you have more "Object Defaults" then there is standards?
I ask because everytime I create an additional one and don't have a standard for it to link to and I save the styles it disappears.
Can you have more "Object Defaults" then there is standards?I ask because everytime I create an additional one and don't have a standard for it to link to and I save the styles it disappears.
View 2 Replies View RelatedWe have a total of three machine at our office that are running 64-bit Windows 7 with Civil 3D 2013. Two of the three machines have problems with drawings that include AECC_Contours. When you try and start a polyline or line the mouse will begin to jump and lag. As you move the cursor off of the AECC_Contours the mouse returns to normal operation. I have looked around throughout forms and have yet to find anything that relates to this. Also I have disable Aero within Windows, thinking that may have been the issue. All three machines are running the same version of Civil 3D with the latest service pack.
View 6 Replies View RelatedWhile working in a drawing with civil 3D points and a surface created from those points, once in a while the contours will disappear. The contours disappear during any number of different commands, so it doesn't seem to be linked to a specific set of commands. If we save the drawing, close it, and then open it back up the contours are there with no problems. Is there a fix for it beyond closing and reopening the drawing. We are using Civil 3D 2010 in our office, and all of the current updates.
View 5 Replies View RelatedIm working in Civil 09. I need to adjust the surface I created in order for the contours to be correct. Right now I'm interpolating point elevations to adjust the contours. I find myself adding lines and adding and deleting points. It's tedious. I tried changing the grid spacing to smaller one. It didn't seem to work.
View 9 Replies View RelatedI have a surface with a bunch of contours. I want to view the contours at elevation 550. In Microstation there is a set display depth command. Is there a tool in autocad where I can view certain elevations.
I want to make layouts/viewports that are clipped to different elevations. For example I have a surface with 5' contours. I want to create multiple viewports on a sheet showing what each contour looks like at its elevation.
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
I encountered a problem while creating contours from the points. what actually is the problem with the points or tell the steps once again that would be great. I'm attaching the points file.
View 9 Replies View RelatedI'm running 2012. Is it still true that I need to label my contours in every drawing? I have a drawing that contains my existing surface (about 90 Acres). I have labeled the contours in that drawing. I then have a output drawing that the existing contours are a data shortcut. The contour labels do not show up.
View 3 Replies View RelatedI am having an issue with my contours running through my breaklines (feature lines). I have tried re-ordering the breakline, edits, etc and have also set my settings to allow crossings.
View 9 Replies View RelatedWhenever I zoom out in a drawing in Civil 3D with surface contours, some of the contours disappear. I imagine this is a result from a system variable setting but could not find it.
View 2 Replies View RelatedThis is the first time I have imported a .dgn file into Civil. The drawing contains contours lines with Z elevation data. When I create a surface using this geometry (polylines + some lines) the surface seems to be scaled in the Z axis by 12.
For example pline (from dgn) is at elevation 46' but the Civil3D surface is 552'
I assume this is a setting in the Surfaces dialog box, but I cannot find it.
Also the elevation field in Properties from the dgn contours is weird. For example, in one area the (pline) contours display -28', 26', -24', -22', -20', -18' in Properties but Civil3D interprets this as a downward slope - which is the actual field conditions. I don't understand the conversion going on here.
The geometry of the pline and contours generated from the surface seem to line up in a side or isometric view (see attachment).
Often I've found myself dealing with some pretty complicated surfaces that have a lot of nooks and crannies, and many of the contour lines are only in a corner of the surface or are small and closed, and thus when I find myself wanting to have contour labels on all of the contours, there's not really one line I can draw using the "Create Multiple Labels at Interval" option to ensure that every contour is labeled. Thus I end up doing "Create Multiple At Interval" with a few different lines intersecting contours, but I often end up hitting some of the contours multiple times and I get a mess of labels.
I haven't been able to find a way to automatically just multiple labels on all of the contours at an interval in one fell swoop, so I started trying to program one...but then I got stuck with that, too.
Does any built-in method of doing what I want to do, or do I need to continue pursuing a programmatic solution?
trying to create a model from existing polylines (at elevation). I have created a surface, went to definiltion, drawing objects, but there is no "polyline" option there. I must be missing something. How can I create a c3d model from existing polylines?
View 9 Replies View Related