I've been researching the options to deal with tessellation of my corridor. I see the option to extract feature lines from the corridor and to maintain a dynamic link.
I've now found a link in the docs for converting tessellated lines to arcs. Can I use this command with a dynamically linked FL? And will it maintain the dynamic link? [URL] ....
I was looking through the docs and all it says is that this eliminates tessellation. I understand that and that's what I'm looking to do. But the docs don't give any guidance on what these numbers are for.
I'm talking about the three options under the "Smoothing" group - "Horiz Deviation", "Weeding" & "Arc Inclusion" (I'm looking at the 2010 docs as that's all I could find at the moment).
I am building a corridor with the right side of the pavement fitting to the existing surface.The subassembly used to link the edge of pavement to the existing ground is LinkSlopeToSurface.
On the corridor created, the feature line (code P2) of the corridor surface (top) starts from the station 0+025, instead of 0+000.
I was wondering why there is no feature line P2 for station range 0+000 to 0+025? Does that mean the linkage to the existing ground surface not exist for the slope defined in the subassembly?
I have a corridor with the two daylight points marked as BOUL BOUR.
View 2 Replies View RelatedI created an assembly using BasicLaneTransition. When I apply it to my corridor I am not getting a feature line at the crown (center) of the road. I have used this subassembly on several other projects and have not had this issue. The only difference I can think of is that the other projects we started in C3D 2009 and this one is in 2012.
How do I get my feature line to show without adding a marked point?
Civil 3D 2012 SP3 | Win 7 64-bit SP1
Xeon E5-1620 @ 3.60GHz, 16GB Ram | NVidia Quadro 600
I have created Road 1 and assigned Feature Line Styles in the Feature Lines tab of the Corridor Properties and it looks as I expected.
When I go to Road 2, 3 etc I have to manually assign the Feature Line Styles again, so the question is can these feature line styles be assigned via a code set or something.
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
I cant seem to target a corridor FL and keep it linked to the corridor. Is this the expected behavior? I would think you should be able to, no? For that matter I would think you should be able to pick the cooridor link directly, no?
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
Is there a way to be able to choose a desired feature line when extracting from a corridor? For example, when subgrade and finished grade are on top of each other, it seems subgrade is always coming as default for extraction. I'm not getting the option to select the desired point code as usual for some reason. The best way I found is by turning off the subgrade feature line from the corridor properties, which is a bit tedious.
View 3 Replies View RelatedI have daylight_cut at say station 100, then sampled every 20m, however it connect from station 100 all the way to 1000 for example. because there is no such code in between. why can't it create seperate features lines? the thing is sometimes it does it and sometimes it doesn't.
see the redline cutting across the corridor? shouldn't be there.
I have grading style set up to create a cut/fill boundary and the same thing for my corridor. I made surfaces from my grading and corridor and no longer need them. I need to keep the cut/fill lines for my design. How can I extract these lines from these objects? I tried keeping the grading/corridor on one layer and lines I wish to use on another so I can turn pieces of the grading off. However, it will not print the cut/fill boundary without printing all the feature lines created from a grading.
View 1 Replies View RelatedCan you reverse the direction of an auto feature line generated from a corridor in C3D 2012?
View 4 Replies View RelatedIs there any way to do that (workaround method).
View 3 Replies View RelatedI am using the Mill&Overlay sub set to overlay an semetrical road and a crown offset of zero. I one file the crown point feature line has gaps in it and in another file it zig zags along the road.
I forgot to mention that the triangles and the cross section look as expected. trouble is I want the crown profile
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
I have a road corridor with feature lines connecting the road edges (cyan), ditchline (dark green), daylight_cut (yellow), daylight_fill (green) and daylight (white). At certain random locations along this corridor I am getting feature lines which span from one station to another, ignoring all of the corridor sections in between. The image below shows a daylight_fill line spanning over 60m, even though there is a daylight line through this region.
In this area a ditch line and a daylight_cut start at 4+110, skip over the next cut section at 4+120 and jump over a hundred meters to the next piece of ditch at 4+280..This corridor builds clean - no error messages reported.
Is this the only way to extract feature lines from a corridor i.e. selecting each one - it gets a bit tedious.
Is there any method to select a corridor and extract all the feature lines that are set to display?? I think third party software (Sincpac?) can do this but this is not an option for me and I am not well versed enough in .NET to write something to achieve this myself.
No feature lines in offset corridor
View 3 Replies View RelatedHow do I make my corridor feature lines to change color? I want daylight cut to be red and daylight fill to be green.I've checked under "Toolspace/Settings/General/Multipurpose styles/Feature line styles/Corridor daylight line - Cut" but it doesn't work.
View 4 Replies View RelatedMy corridor Feature Lines for Daylight Jump across in different areas (see attached PDF)
when I look at it in 3d it looks ok but the plan view the jumped lines show up.
How do i get the feature lines in my corridor to change their style based on the code set style selected?Whats the point of defining featureline styles in the code set style if they don't change in the corridor? They only get used when you first create the corridor?
Is there something I am missing or is this the intended workflow?
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
i have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
View 3 Replies View RelatedI have problem with corridor surface boundary , in curve boundary line is jumping on daylight fill , but i have created surface on wearing layer ,also when i am adding boundary there is only 3 types of adding , corridor extends , polygon and interactively , photo attached.
I am using Civil 3D 2014
Is there any way to project feature lines into a profile when the plan view is xref'd? I have my plan view "existing topo" with all existing features/Figures and a existing surface.
My profile is a separate dwg with plan view xref'd and surface a data shortcut. Of course there are feature lines and Survey Figures in the existing top I want to project into the profile, but can't because it is an xref. Besides copying .
C3D 2012. I am trying to get the distance from the start of a featrue line to a selected point. My object is "FLobj" and my Point is PT1. I am using the method Get2dDistanceAtPoint. This is the line of code.
(vlax-invoke-method FLObj 'Get2DDistanceAtPoint pt1 'pDistance)
I keep getting "too many actual parameters".
I am wanting to add the name of my feature line to a label style. I am trying to create a label style that will show Lot Number and Area. I know i can create parcels, but i dont want to! I have also created a map table that can do exactly what i want on polylines, but will not work on an xref. Labelling featurelines does work in xrefs.
how to add the name into a label style?
Is there a way to decurve feature lines like how we do it with polylines? I am labeling my feature lines but don't want the curve labels to show up
View 6 Replies View RelatedI am building a surface and have back of curb, curb face, and curb flowline going around a curve. I cannot create the lines with the usual pline as they will cross due to poor field collect. I created the curbs with multiple arcs. I was then going to change them into Feature Lines and am wondering if I can then use them as breaklines in a surface.
View 1 Replies View RelatedI have a roadway alignment with FG profile and I want to place a feature line on the roadway centerline that represents the FG profile elevations.
View 7 Replies View RelatedWe have cooridors with features such as terrace drains and flowlines, but we cant seem to get the linetypes to show up correctly. For example a flow line should have arrows but it shows up without the linetype and looks continuous.
LTSCALE =1
MSLTSCALE=1
PSTSCALE=1
DRAWING SETTINGS - 1"=40'
CIVIL 3D 2012
We are running Civil3d 2012. When converting a line or 3d poly to feature line, or just creating one it adds elevation points where it crosses surface breaklines even if you do not assign elevations. We want the feature to just have 2 elevations. The beginning and end. Is this a bug? Or is there another setting somewhere?
View 7 Replies View RelatedI created a label for retaining wall that takes the z value from the start and end of a feature line. Works great except that it isn't dynamic. I have created the feature line in a grading sheet where the surface is data shortcut into it and I'm just using grips to make sure the ends are on the bottom and top of the retaining wall. Is there any way to dynamically pin/tie the feature line to a surface that has been data shortcut?
View 9 Replies View Related