AutoCAD Civil 3D :: Anyway To Activate - Deactivate A Surface?
Mar 11, 2013I'd want to have a way to activate or deactivate a surface ,
View 9 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: How To Activate Or Deactivate Icon
Apr 16, 2012How to activate or disactivate this icon (the one with two arrows): I think it has a relation with large surface visualization.
View 2 Replies View RelatedPhotoshop :: Deactivate/Activate After Install On Vista
May 2, 2008I am going to install Vista Ultimate (Have XPpro now)
This will mean a formate of my C: drive (160 gb programs disk) and clean install of Vista.
Do need to de-activat Photoshop CS3 (and Lightroom) and re-activate after I install CS3 in Vista?
Photoshop Elements :: How To Deactivate One Station And Activate Another
Jan 4, 2014I have several computers at home - it seems only two can be activated. How do I deactivate one station and activate another?
View 1 Replies View RelatedAutoCAD Civil 3D :: How To Correct / Manipulate Surface To Show Proper Flat Surface
Dec 2, 2011I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
AutoCAD Civil 3D :: Reduced Maximum Length For Surface Triangles Causes Surface Holes
Oct 22, 2012Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
AutoCAD Civil 3D :: Editing Existing Surface Using Edit Surface Command
Nov 14, 2012I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
AutoCAD Civil 3D :: Volume Bounded By Existing Surface And Design Surface
Dec 10, 2012My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
AutoCAD Civil 3D :: Add A Surface To Blank Drawing / Then Upload DEM Files To Surface
Oct 2, 2012I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
AutoCAD Civil 3D :: Change Reference Surface For Surface Elevation Label
Apr 4, 2012Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011
AutoCAD Civil 3D :: Import Surface Into Revit To Merge Surface And Buildings Together?
Jul 29, 2013I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.
The questions:
Would it be better to import the surface into Revit to merge surface and buildings together?
Would it be better to import the buildings into C3D to merge entities?
Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?
AutoCAD Civil 3D :: Creating Subset Surface From Main Surface
Sep 15, 2013I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.
i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline. This seemed to work, but when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.
AutoCAD Civil 3D :: Create Cut Fill Surface From Existing Surface
Mar 1, 2013Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
AutoCAD Civil 3D :: Corridor Surface Will Not Paste Into Empty Surface
Mar 26, 2012all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies View RelatedAutoCAD Civil 3D :: Can't Use The Corridor Surface As DATUM Surface
Feb 7, 2013My problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies View RelatedAutoCAD Civil 3D :: Adding Corridor Surface To EG Surface
Mar 6, 2012I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
AutoCAD Civil 3D :: Trim Surface To Another Surface
May 3, 2013I was wondering if there is an easy way to trim one surface to another. Right now, I have two slopes (3:1) that are perpendicular to each other. They meet at a corner and I have extended them past each other so that I could see the intersecting edge. Now I would like to trim them to each other like you would a polyline etc... but I am not sure how to do this.
If I select surf trim, it tells me they are the wrong object type, but they are tin surfaces?
AutoCAD Civil 3D :: Surface Boundary Only Showing Portion Of Surface Within The Boundary
Oct 24, 2012I used a 2d polyline to create a surface boundary for a surface created. The polyline is a closed loop. For the boundary type it is outer, unchecked Non-destructive breakline, and mid-ordinate distance = 1.
My problem is that when I do this I only get a small portion of the surface to show up within my surface boundary. If I don't have a surface boundary the entire drawing surface shows up no problem.
The purple polyline is my boundary and the light blue is the surface created within the boundary.
AutoCAD Civil 3D :: Export Created Surface From Civil To Revit Architecture
Dec 17, 2013Is it possible to export created surface from civil to revit architecture? If yes , How? And if its not possible - maybe i can somehow import cogo points to revit?
View 6 Replies View RelatedAutoCAD Inventor :: Deactivate Add-in With VBA / VB
Oct 2, 2012How can I deactivate an add-in with vba or vb.net?
View 4 Replies View RelatedAutoCAD Civil 3D :: Surface From Grade
Jul 28, 2013I'm working on a grading plan which excavates down from just outside the waterline of an existing pond. When I create a surface from the grading, it looks like a whole bunch of strange break lines have been added, messing up the surface. I thought it might be the mid ordinate distance but changing that doesn't seem to fix it it. Interestingly, when I grade from the original waterline, this doesn't seem to happen.
Here is my workflow, a picture of the result is shown below.
1. Turned the current waterline into a feature line.
2. Created new feature line by offsetting outside that feature line by 3.16 ft.
3. From new feature line, grade down 10 feet at 3:1
4. Create new surface using grading.
The grading lines (shown in white) look correct. But when I create the surface (green and yellow), it is all messed up.
AutoCAD Civil 3D :: Creating A Top Surface?
Dec 11, 2013If I change a point or link code in one of my subassemblies, is there a way I can build my top surface using those?
View 9 Replies View RelatedAutoCAD Civil 3D :: Can't See Surface - Turned Off
Jul 8, 2013I know my surface is there but somewhere I have turned it off.
I know the surface is there but I'm not able to see it.
Can you paste a surface from a different dwg?
AutoCAD Civil 3D :: Where Is Corridor Surface
Mar 21, 2012When i try to create a material list, i don't see my corridor surface - just the EG surface appear in the list.
View 2 Replies View RelatedAutoCAD Civil 3D :: Subtract One Surface From Another
Nov 24, 2009I am in need of subtracting Surface A from Surface B to display the surface intersections between the two. I have a geological top of clay surface and a bottom of clay surface where the bottom intersects with the top thus showing holes in a geological clay layer. I am wanting to know if Civil 3D supports the subtracting of two surfaces.
View 6 Replies View RelatedAutoCAD Civil 3D :: Create Surface On Something Other Than WCS
Aug 3, 2012Can a surface be created from a UCS that is something other than the WCS? For example, can you create a surface for a vertical wall, or a battered almost vertical wall?
View 2 Replies View RelatedAutoCAD Civil 3D :: Read Surface From Another DWG?
Feb 29, 2012In LDD the surface, alignments etc were easily accessable in any dwg in a project.
How can I do this in C3D?
AutoCAD Civil 3D :: Exporting Surface As DEM
Aug 3, 2013I'm trying to export a surface as a DEM so that I can import the object into Bryce 7.1. I have a number of sample DEMs that I have downloaded from USGS site that import into Bryce quite nicely. These samples also import to another DEM reader named "3DEM Version 20.7." I'm able to import into Bryce when I set the grid at 10, but the quality of this surface/object is not very good. The DEMs from Civil 3d are referred to as "USGS DEM"s, but they do not load on common DEM readers such as Bryce or 3DEM software. Any way of converting a C3d DEM to a USGS DEM that one of these other readers can import?
View 1 Replies View RelatedAutoCAD Civil 3D :: Add Contours To Surface
Nov 20, 2013I have added contours to my surface (the blue lines). For some reason the surface generated contour (the orange line) is jumping across the contours I've added.
View 8 Replies View RelatedAutoCAD Civil 3D :: Get Surface Breaklines
Dec 4, 2013I have this:
for(int i=0;i<= tinSurface.BreaklinesDefinition.Count-1;i++) { .................
}
I have each breakline sets, but I want each breakline of each breakline set(breaklinesDefinition).
I can do this:
Autodesk.Civil.DatabaseServices.SurfaceBreakline sfb = default(Autodesk.Civil.DatabaseServices.SurfaceBreakline); SurfaceBreakline sfb= trans.GetObject(id,OpenMode.ForWrite) as SurfaceBreakline;
But how can I get ObjectIdcollection of surfaceBreakline of one breaklinesDefinition?
I have seen that there is "AECC.Interop.Land.SurfaceBreaklines". Do I have to use this?
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
AutoCAD Civil 3D :: Copy TIN Surface
Aug 31, 2012I've been wondering if there´s an easy way to copy a TIN surface or at least an easier way than what I'm currently doing. What I do is:
- Exctract objects > points/contours depending on the surface and border
- Create a new TIN surface
- Definition of the new surface > add point group or add contours
- Convert the 3D poly of the border to a 2D poly
- Definition > add border
I'm looking for an easier way that would save me the trouble of isolating the points or contous because my drawing has too much data and its very time consuming. Isn't there a command that lets me copy a TIN surface which creates another with the same objects as definitions?
