I am trying to create a sheet metal punch tool, however, I must have something incorrect because the extract iFeature does not seem to be working.
I've attached a copy of the file I'm currently working on.
I am trying to make a punch tool in inventor for sheet metal. I noticed that for the features I could not select faces or flanges I did. I know you can extrude the same shape to get the same result but I wanted to use a face/flange so that I can retain the flat development. What is the best way around this.
To get a sense of what I am trying to make:
-square cut out
-on the bottom edge of the square I made a face that is angled at 45 degrees
It would be closest to a louver tool.
I have made some punches for sheet metal and this one seems to be simple but it has me stumb.
Its 50mm in Dia a 5mm lip a 28mm outside rad cone and a depth inside of =/- 8.5mm then there is a 12mm hole
When placing a puch table in a flat pattern drawing, can the origin point be placed anywhere or does it have to correspond to the origin point of the Inventor drawing (0,0,0)?I placed the origin point at some point which I randomly chose but no table popped up for me to chose the puch table option.
View 3 Replies View RelatedI am beginner in inventor, and I have to create punch and put them in library so it can be used later.
View 9 Replies View RelatedHow can I create a sheet metal jog? Like the attached. I used a contor flange to creat this one, but I have to add a jog to an existing part and don't want to have to totally redraw it just to get the jog. I'm hoping you can add it like you can a flange.
View 9 Replies View RelatedHow to create this bend using the sheet metal mode. The bend should be a certain radius on the top (see attachments).
View 3 Replies View RelatedThe question is if I have designed a part in sheet metal with multiple flanges and one of my edges follow a specific radius. Is is possible to use contour roll or any other means to create a flange on that edge that will allow me to flatten that out. I cant see it being physically possible putting a bend in there as the material would need to stretch and the bend tool would need to follow that radius.
View 2 Replies View RelatedI have a sheet metal part. It is a machine door with four edge flanges. I have mirrored this part. The origin part has flat pattern while the mirrored creates the folded pattern.
It still folded even when origin is in flat pattern.
I am getting an error message (see attached) when trying to create a contour roll using sheet metal, I have tried editing the sketch to open loop however I cannot get the contour roll to preview on the part.
The part is a short length of square hollow section from which I am trying to apply the roll to, there seems to be a problem in projecting the geometry on the end of the part
Inventor 2013 SP2 64-bit edition
Product Design Suite Ultimate 2013
64-bit HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I am trying to make a chute out of 4 pieces of sheet metal. Is there a way to take a solid lofted part, shell it, and then break off each side of the the object for cutting and welding them together. I have an example attached.
View 9 Replies View RelatedIn Inventor 2010 we have a sheet metal, with a lot of different straps. But we cannot create round jogs between them. It's only possible, if all straps are created at the same time with the same size etc.
Please see the attached file. The upper version, is the one, it looks in the moment and we want an apperance like the lower one.
Is it possible? Because we cannot add all the round holes later on in development of the sheet metal.
I have to create a conus from a 2mm thick RVS plate, I know how to construct this in Inventor. But how can I create the flat pattern of this form?
Inventor 2013
Im trying to create a shape like the attached image using sheet metal loft from one sketch to the second sketch. No problem doing that but i want to extend the neck on the small end 1 inch like the attached image.
Currently the product is produced using 4 panels brazed together. I want to create the product with 2 bent panels 90 degrees that are split apart from the loft.
Not sure if this even possible in the real world sheet metal house to develop the flat pattern.
Is there a way to create an insert notch in a sheet metal part?
View 4 Replies View RelatedTrying to create a strength bead on a sheet metal part.
View 1 Replies View RelatedWhere I can get a sheet metal iFeature to create nail holes or extruded holes?
View 1 Replies View RelatedLet me start by saying that we rarely use sheet metal parts so I'm not real familiar with that interface. That said, I can create sheet metal parts with square shapes and bends just fine. However, I'm currently stumped as to the best way to model what should be a pretty simple plate.
We have a large, thin (1/8") square plate to which we want to add 2 opposing diagonal very slight breaks to add stiffness to the plate. More specifically, we want these diagonal bends to cover the center part of the plate leaving about a 2" flat flange all the way around the plate.
I'm attempting to create a mini version of a product, I use the Derived Component button and scale the part down. Then I use Convert to Sheet Metal, set my sheet metal defaults, but then nothing happens when i try to create flat pattern. Is it even possible to derive a flat pattern from a scaled part?
View 5 Replies View RelatedI have a part that is derived from a surface skeleton ipt. The derived surface is thickened and then some holes are added. Then, when I try to add a flange, it gives me the error "Sheet metal features are not supported in multi solid body parts". My part is a sheet metal part and single body.
INV 2013
The company I work for has a large number of Left Hand and Right Hand sheet metal parts. To reduce the amount of time needed to create both Left Hand and Right Hand sheet metal parts, I use the Derived Part icon. I create a Left Hand part, use the derive icon with mirroring on and create the Right Hand part. While the Right Hand sheet metal part gets created, the Right Hand part will not allow me to create a Flat Pattern.
what steps must I follow to create a derived sheet metal part that I can make a Flat Pattern with?
I am trying to convert punch .ipt 2013 version file into a Sheet Metal Punch iFeature...For an unknown reason to me i cannot get it to work...Have a look at the file and see why i cannot convert to a Sheet Metal Punch iFeature ?
The Punch will then go onto the Sheet Metal Plate
why the Punch i created causes the following?
1. The punch will not work with part 1.I have 4 points for the Punch on part-1
2. When attempting to get the 4 punch holes on to the flat sheet it causes inventor to shutdown.I have done 4 attempts to fit the punch into the flat sheet (part-1) and 4 times it has shutdown Inventor
A colleague & I have been trying and failing all day to create a punch tool from scratch. I did however manage to modify the geometry of the Dimple & Hole example here:
[URL].....
how to
a) build the iFeature correctly and
b) how to then extract it so that the orientation is not FUBAR when you insert it using the punch tool.
Attached are the dimensions I need. This shape when revolved about the centreline should produce a 'dimple' effect in the sheet metal part.
A collegue asked me about this as he has been given a part to model and the details are for the flat sheet not the finished model. Is this possible in 'sheet metal'? I had a quick play but couldn't work it out. Im used to creating the finished part and 'un-folding' to get the flat pattern.Detail supplied below.
View 4 Replies View RelatedI want to know if is possible to create a troquel punch as iFeature for just bend, not cut o drilled, for example, to create a squared punch for to make a bending in a sheet metal,
View 1 Replies View RelatedMy company is trying to put some automation together to pull design attributes of parts and assemblies to drive routing creation in the shop.
The issue that we have run into is that for certain ifeatures, we need to gain access to the name (or punch ID) of an ifeature (primarily punch tools). Pulling the name of the feature that the tool created is relatively easy, but because you are able to change the name of the feature as it appears in the model browser, it isn't the most reliable way to get that information.
We are looking for a way to figure out what the name of the ifeature used to create the feature without referencing the resulting feature's name in the model tree.
I've included an example, and I'm looking for the name of the tool which should be "Ob_750X562".
I'm using Inventor 2014.
I created a Punch Tool iFeature, everything seemed fine, I could save it without problems.
However, when I try to place it in a part with the Punch Tool, it says "The file has 0 volume changing features. To be a valid punch tool, the .ide file must contain at least 1 sketch-based feature."
I want to create a large sheet of metal, like 1600x1600.
But I don't want it to look too uniform, just too plain. And I want it to look more realistic than a simple grayscale gradient.
This is what I got from fooling around for a bit:
I just what to cut a sheet metal,
and I don't know how (see in Capture.JPG where i what to cut, and test.iam what I what to cut).
Where is the icon "project the geometry" ?
I need a flat pattern for this part but it seems impossible. STEP 2 illustrate the desirable result.
View 7 Replies View Related