I was just wondering why there is no base unit for parts based on Area?
I model a lot of parts that are made from Plate.
When you order or sell plate it is usually sold by the Square Meter
The same would go for Square millimeter, Square foot etc.
Also other base units would be handy like Pack, Box, Carton I am sure there are many more.
The main one I really can't do without is Square Meter.
Is there an easy way to put sum of all values in column in parts list?
I would like to sum up mass column to get overall mass in the end of table. Is there a way to do so?
I also have problem with units formatting. I have QTY column in parts list. Some parts are listed in EACH and some in MM. I have lengths given with format 120,000 mm. I would llike to set this to be rounded to full mm but I can not acces this setting for column because in some raws I have EACH unit. How to format it right without manually overriding?
I want to know if there is an easier ACAD solution for drawing. In the given triangle of ABC (sides and angels are known) I want to draw line CM so that the area of BCM becomes 2000 cm (are of ABC is 5311.7 cm3).
Is there an easy ACAD way for drawing this line without using trigonometry for calculation?
Inventor 2012.how would I input the total quantity of doors in the .iam in order to update the Parts List quantity column? I have a lot of user inputs in the .iam file set up to change width, height, etc that are based off of Parameters in the .iam, but I don't know how the user can enter assembly quantities in order to get the Parts List to update the Quantity column correctly?
I have attempted using custom iProperties but how to get it to display based off a user input Parameter.
I have a macro that I acquired somewhere (possibly these boards, can't remember now) for placing a parts list. I have modified it somewhat to change the location on the sheet where the list gets placed, as well as a sub that starts the autoballoon command afterward.
The macro is set up to place the parts list in the upper left corner, by adding the parts list width to the Mini Point of the border. This works perfectly well, except that we have two parts list styles, and they are differently sized.
What I would like to do is have the macro detect the parts list style, and change the offset value depending on which style it finds. I am an extreme novice with the API, who basically knows just enough to tweak sample code a bit, and have not been able to find anything close enough to use as an example.
How I should go about this, or even post some samples of something similar? Current code is shown below.
Public Sub CreatePartsList() On Error Resume Next ' Set a reference to the drawing document. ' This assumes a drawing document is active. Dim oDrawDoc As DrawingDocument Set oDrawDoc = ThisApplication.ActiveDocument 'Set a reference to the active sheet. Dim oSheet As Sheet Set oSheet = oDrawDoc.ActiveSheet ' Set a reference to the first drawing view on ' the sheet. This assumes the first drawing ' view on the sheet is not a draft view. Dim oDrawingView As DrawingView Set oDrawingView = [code].......
The macro does not have to set the parts list style - that is controlled by the drawing Standard. It just needs to detect what it is, and place the list accordingly.
Possible to display Part Area in a Column in a Parts List on an idw?
View 3 Replies View Related" Convertion of AUTOLISP base routines to Diesel MACRO based routine to be used in a AUTOCAD LT based platform "
Here i am attaching the lisp file for ready reference.
i have a number appear when a get the AREA of the attached rectangles shapes especially when i use SMD ucs.for instance see the rectangle C07 74 X 39=2886.00000000 BUT i get the area like 2886.000000003.why the precisions doesn't all 0...
View 7 Replies View RelatedI have a project with several parts that all fit together. I understand how to freeze all of the parts that I don't want in a viewport but how can I do the same for a base view?
I would like to have one layout with an exploded overview of all the parts and then a separate layout for each of the parts. Is it possible to freeze the parts I don't want within a base view like you can within a viewport?
I have an irregular shaped polyline in civil 3d that needs to be 31.5 acres. It is currently 32.8 acres. Without manually rescaling this polyline over and over again in order to achieve a polyline that represents 31.5 acres, can Civil 3D automatically draw the polyline to represent 31.5 acres for me?
View 9 Replies View RelatedIn Civil 3D 2013, when I execute the _area command, i get results in square feet as opposed to acres. Under the ambient settings, the area unit is set to acre. how to get C3D to display my area in acres? I just want it to list the area, not label it.
Also, is there a way to get it to display the area in BOTH acres and square feet?
in order to streamline some of my duties i wonder if theres a way to have a dynamic block not only that can change it's length and the dimension for that length (easy) but will also add features to the part. For example can one be made that when stretching its length that once it reaches a certain length automatically split into two sections and keep those 2 sections equal? Also can it be made to contain a tag that keeps track of the lengths as well as number of joints between sections multiplied by a constant?
View 1 Replies View RelatedWe have 1 machine in the office that when using super hatch it will not "hatch" the entire area as one hatch, it breaks it into separate image based pieces. The rest of the office, it hatches as one entity so it can be changed easily. Even if we use the group command, it will not group them.
View 2 Replies View RelatedI want to divide an area in 3 equal part in autocad civil 3D,but I don't know how?
View 6 Replies View RelatedIs it possible to add a base depth to the transition lane assembly? I need to do volumes for my road, (pavement, base) but there is a section with a transition (which only has one depth), so that section is off.
View 5 Replies View RelatedI am trying to replace a custom part - created from a content center part - with a copied part with a different name. (I am using the replace tool in an assembly.) However, Inventor is not replacing the part with the part I pick but rather the content center version of it.
View 3 Replies View RelatedOn the main sheet of my drawing I have the overall Parts List. Shows almost all parts except for the few that we don't want to list. On the second sheet I inserted a Parts List to show only parts that are shown in a detail on that page, made the rest non-visible.
On the main sheet there is an item (#13) that has a QTY of 3. Two of those Three are optional parts. What I'm trying to do is insert a custom part into the Parts List, give it an item number of 13A and put in the description "OPTIONAL", then do an Override in the balloon to show 13A.
I get it in the Parts List, Apply it, close it, save the drawing. Looking at the Parts List, item #13A is there, but item #14 is gone. I go back into the Parts List and 13A is there and there's a blue box around the item # and the description. I uncheck Static Value and number 14 shows up (item # and the description).
Then I go over to sheet two, open that Parts List and it lists 13A at the bottom with all the info I added in sheet one and it's non-visible. Go back to sheet one, open the Parts List and there is no 13A to be found.
I am working on an assembly that is designed around a box (bounding box) that could change size. I modeled the bounding box and placed it in a new assembly file. All other parts have been created within the assembly by referencing that bounding box with starting work plane and project geometry.
The problem comes in when I change the bounding box dimensions. The work planes for each additional part, which were defined by the faces of the bounding box, do not move when the sides move. Also, my projected geometry is not updating correctly. This is a simple box, with all 90° corners. So, all associated parts (at this point) are just rectangles.
My parts list on my idw do not update when I make changes to the model. Specifically, I have deleted a bolted connection on my design and replaced with a different components but the parts list table does not update - all I see is a lightning bolt in the browser next to the parts list but I cannot update it here.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I was using virtual parts to add nuts and bolts to a drawing in 2013
I can make a VP bolt in the assembly, no problem, set it's size, weight, etc.
In the VP itself, there is no option for number of bolts I want it to emulate. For arguement's sake the weight was 1 pound per bolt (they are big bolts).
I can go into the BOM and say quantity 60, hit done and save the assembly.
If i open the drawing, the parts lists shows 60lbs for the 60 bolts total - which it should when summing the weight.
The problem is the BOM/assembly. If the weight of my assembly (without bolts) is 10,000lbs, the assembly sees the VP weighing 1lb and says the total weight is 10,001 lbs. Am i going to have to pattern a fake part to get this to work right? Shouldn't the total weight take into account the quantity set in the Bom??
Is there a way to display the density of materials that are assigned to varius parts in the parts list on a drawing? I don't need the mass of the parts I just need the material density to show up next to their respective parts.
For example, if I have a part with [steel mild] material assinged to it (no matter the size) I need a column in the BOM on the drawing to show: 490.684 lbs/ft^3. "Worry when there's something to worry about."
I have an assembly with a lot of purchased parts. I need to create a buy out list for purchasing. I've done this many times in the past and have a template set up for this purpose.
So now the problem, In this assembly, I have subassemblies showing up on my parts only parts list.
One of the subassemblies cinsists of two purchased parts. Both parts are set to purchased in the Bill of materials. If I do a parts only list on this assembly, it works as expected, showing two purchased parts. However, if I put that assembly into a higher level assembly, A parts only parts list shows the assembly instead of the individual parts.
IV 2010 Suite
Been working over an idw MANY times due to project lag.Today I opened it up and tried adding balloons to an already ballooned assembly.
The parts list has not changed, and is "structured".But, if I try adding balloons, they tag each part, not the entire assembly.
Also, I verified this by trying to add another parts list, which defaults to "parts only".
I can't show my data set, b/c it's HUGE, plus it's proprietary.
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I have a .idw that I'm trying to make a parts list on. I select parts list and highlight everything. There are two screws that are not showing up on the parts list. I cannot select them manually either. It's acting like they are not there. Even if I do a complete parts list (adding the assemblies parts into one big list), they still don't show up.
How can I select these parts? What is wrong with them that they do not show up in the parts list?
I have been working with an assembly today where it is ideal to mirror parts and have figured out how to reuse the parts rather than create new parts. Now I find that when the parts are mirrored, they ate not retaining the mates. Where do I find the setting so they either retain their mates, or prefferably retain the mirror so that if I move the origional, the mirror moves as well?
View 9 Replies View RelatedWhen I use the Fuzzy select tool or the select by colour tool, how can I remove the selection area around the parts that I don't want selected. For example. I have red car on a white background which I want to cut and paste to a black background. I select the white background, but although it selects all the white, it also selects other small areas on the car which are a similar colour. If the threshold is lowered too much when I use these select tools then I get a very small white border around the object when I paste it on to a dark surface. So instead of selecting using the default (15) or even less, I have to ramp it up so as the selection is closer to object and does not show the white jagged line. I thought that I could use the other selection tools with the "remove from selected" option selected, but each time I place a rectangle around the selected area that I want ot deselect, it does away with the entire selection area. I just cannot get it sussed.
View 4 Replies View RelatedIs there a way in the description field of an Inventor hole table to have mixed units? Some hole sizes at fractions, some at 2 plc, and others at 3 places.
Inventor Pro 2013 or 14
I want to make some points in 3D sketch base on the Coordinate System that I defined (UCS).Is there any solution to make these points in 3D sketch just by inputing their coordinates in my UCS?
Example: the new UCS origin has (x,y,z) coordinates from the origin.and one of the points has the coordinates of (x',y',z') from the UCS.
So from the origin it has the coordinates of (x+x',y+y',z+z').Is it possible to just use (x',y',z') from UCS directly to get my point?
I was wondering if there was a way to change the model my base views were linked to.
If I wanted to link the base view to a different model, would this be possible.
When I double click on the base view it shows the file path for the model that is currently chosen; however, it is all grey and I am unable to edit it or choose another file path.
How to change this? Is this even possible? Is it because I have annotated the drawing view that I am unable to change the model path?
what could have happened in an assembly when I've changed the cube front view (3D)? The projection has changed automatically (the view) in 2D. In other assemblies didn't happened the thing I've mentioned before even if I did the same thing meaning that I've modified the front view but 2D stayed in the same projection.
View 1 Replies View RelatedWhen starting a new idw, my first action is placing the base view. I would very much like to start a new 2D and have the "Drawing View" window automatically pop up. I'm not sure how to do this. Would it be part of the idw template, or is there a setting I'm oblivious to?
View 6 Replies View Related