how I can combine the bend function & flange in an animation. The problem is that I'm unable to use flange when the plate is nearly 98% flat (which I need to remain the radius for favorite parameters - bend function).
View 9 RepliesI have tried to do a lofted flange. It works, but there is an extra bend that I don't understand why it is there. The bends, I would assume, should be symmetrical but they are not. I have attached the part.
View 5 Replies View RelatedIs it possible to combine 2 movements in 1 animation step. i.e can a part rotate and move along its axis at the same time?
I think I have done this before in the presentation environment, but can it be done within the assembly with studio activated?
How to go about bending blades of a fan. This is a test demo of a project I have to do. I want to solve my issue with this simple demo. I have to make a crashing fan scenario. As the fan crashes the fan blades must bend natural in the animation. This animation will be about 20+ sec long. How would you go about solving this problem
***Example Image is Attached***
I have a simple character with two a leg. The IK chain goes from the top bone to the bottom nub. When I move the ik helper around, the knee does not bend, even though there is a joint for it. Instead the leg rotates only at the top.
Example:
Should happen: (notice bend in knee)
____
/
/
/
What happens:
/
/
/
/
/
/
The bones are all connected correctly as well.
So I'm trying to rig this arm to bend, but with more "bow" than "bend", if you get what i mean..
I thought I could create an IK handle, but at the moment it bends only at 1 joint. I would like it to bend further up the arm,in an arc shape.
I wonder why it will not bend. Why it didn't bend? I attached the PrintScreen of the problem
View 2 Replies View RelatedI have also added the path controller and have animated some rotations (Z axis only for now) as the assembly goes around the path.
My question is - I can duplicate the assembly via the snapshot tool easily enough and they all follow each other as expected...but how can I now copy my previous set up animation onto the new cloned assemblies?
Is there a way to copy and paste the original animation - then either time shift via the curve editor or % on path controllers?
What I have is a bracket that sits on a pitched roof (ipt attached). The part was set up to reflect the positioning. On the lower side of the pitch, the easiest thing was to scuplt the flanges to the slope. Although the flat pattern results in some edges not being perpendicular to the face (See image). These show on the drawing. I realize you can remove these in the drawing but it would be nice to not worry about it.
What would be a better way of handling this situation?
2010 Suite-SP4 64bit
we are 3 students planing a short animated Film for university, the character will be modeled in the next week and we are planning the rigs right now. We thought one guy is doing the Facial Rigging and another Guy the Body Rigging. Is it possible to combine the weight maps etc to get a perfectly working solution?
System:
AMD x6 3.2Ghz
16gb Ram
Nvida GTX 460SE
I made a Robotic arm whose function was to pick a dropper from a beaker and pour the droplets in another beaker from the dropper and then place the dropper back into the first beaker.
I used combine to attach the dropper with the robotic arm; everything worked well but when i placed the dropper back into the first beaker and rotated the arm back to its original position all the groupped objects got scattered ...
I am working on a bin type unit, and am having trouble creating a flange, I am creating the bin in the final product stage, then I will separate into manufacturer components. I am having trouble adding this flange around the top 4 edges of the bin. I need the four corners to meet on a miter 45. I will then rip down each seam and have 4 separate panels.
Is this a bad workflow? Is there a better route? I attached the part in Inventor 2013 format,
I created this flange and I need to cut it from the extruded tube, but I'm having some trouble.
View 2 Replies View RelatedI made a sketch for a bracket and used sheetmetal/contour flanges tool to make solid.I had to use 2 contour flanges to get the shape as i could not get it to work with 1 contour flange.Is this not possible due to something wrong with my sketch?
Other question is have i used the Cut tool correctly for the cut out of the brackets?
Inventor 2012
I'm having no problems creating the contour roll, but it won't let me add flanges to the outside edges. I have attached a file that shows the measurements that I want. I need to be able to create a flat pattern. The material thickness is .1046" and 3" deep.
View 1 Replies View RelatedI made this sheet metal part, selected the arc sketch and the perpendicular edge like in the picture, but the contour flange isn't created
View 7 Replies View RelatedI am trying to make a way that suppress the flange features of all the panels that will be insert in the assembly so i can suppress all the features at ones in a assembly and don't have to do that for each panel separately.
I have a assembly with parameters and i have a part with no geometry but have linked the parameters from the assembly. In my panel part i link the parameters to the part with no geometry.
When i use the parameter in the assembly to suppress the flanges that works the way i want it. But when i insert the panel part into that assembly it doesnot work.
I am trying to create a sheetmetal part and flat pattern of a 72" radius section with 3" split flange top and bottom.I have searched the Discussion Group and several other sites with no results.
View 2 Replies View RelatedIs Inventor able to provide information about the bending angle of a lofted pieces ?
I'm trying to loft a piece from square to circle. The bender ask me what is the angle of this pieces.
I would like to know if there is a way to have the Schedule as an I-Part parameter of a flange. I'm trying to create a custom flange for use in the content center and would like both size and ID to be picked from a drop down when placed into an assembly.
Since it's a flange not a pipe I can't use the standard tube & pipe authoring method.
I'm trying to make this part on Sheet Metal, and I have to offset this flange at 28 degree that meet 0.37". The thickness is 0.12". Currently, the only method that I know how to meet that 0.37" is by playing around (guess and check) with the number in picture 3. Any other methods to create this offset part.
Inventor 2011
Window 7, 64bits
I tried to create a overlap flange in sheet metal, but the result is not what I want as I cannot select the gap edge near the circle portion. I attached the file here.
View 3 Replies View Related1) I have assembly containing pipe and a flange. I want flange size to correspond pipe size. In other words, when parametrically change pipe size, flange size to be updated automatically. ( do i need to have two parts - pipe and flange, or it can be one assembly without need to create parts?)
2) Is it possible to control type of flange (slip-on, weld-neck.. etc) by parameters or need to make different assemblies for different flange type?
3) Then when flange and pipe sizes are updated would like to make overall length of that assembly whole number (since hub length changes with the flange size). how to round that overall length to integer?
I have sketched a fan casing which consists of a series of tangential arcs. The sketch is fully defined but when I try to use "Contour Flange" I get the following error:
Sheet Metal: Contour Flange Creation failed.
19-3-101-26-2.ipt: Errors occurred during update
The attempted operation did not produce a meaningful result. Try with different inputs.
Try decreasing bend radius
Feature Compute failed.
My guess is the end points of the arcs are not defined correctly but I do not know how to fix. I have attached the file.
I am currently working with an elliptic profile that needs to be unfolded. The part consists of two sketches, with each sketch having two ellipses. The ellipses on each sketch then forms a cross-section where the thickness of it is supposed to be 8 mm (the first ellipse is offsett).
My plan is then to generate a mold for the inner and outer sides of this part by using the "Lofted flange" function and Rip, since I want the flat pattern of it. However, I've found that I can not select my offset ellipse when using Lofted flange, only the original one. I'm thinking that this might be caused due to the offset ellipse not actually being an ellipse but a spline (I read somewhere that there are two ways of offsetting an ellipse. One generates a mathematical ellipse and the other a spline). Creating an new ellipse and then saying that the a and b distance should be 8 mm less than the other ellipse will work, but that will not give me a constant wall thickness of 8 mm along the circumference of the elliptic cross-section.
What's the best way to populate the studs and nuts on a flanged connection in tube/pipe? Can studs be added to the bolted connection content?
2010 Routed SystemsInventor Professional 2014 Build 222
Dell Precision T3500, Intel Xeon W3550 3.07 GHz, 12GB RAM, Win7 SP1
Is this a bug in sheet metal?
I pick an edge to create a Flange feature and the Flange is longer than the edge. (Flange4 in the file)
I am trying to make a punch tool in inventor for sheet metal. I noticed that for the features I could not select faces or flanges I did. I know you can extrude the same shape to get the same result but I wanted to use a face/flange so that I can retain the flat development. What is the best way around this.
To get a sense of what I am trying to make:
-square cut out
-on the bottom edge of the square I made a face that is angled at 45 degrees
It would be closest to a louver tool.
Is there an easy way to flange so that the flat pattern comes out with the two sides' faces are parallel to each other? I have attached the part I am trying to work with.
View 1 Replies View RelatedI created a seemingly simple contour flange, and cut away a 890" radius. However, when I try to create the flat pattern, it gives me the message:
440-006.ipt: Errors occurred during update
440-006.ipt (Flat Pattern): Errors occurred during update
Definition1: Could not build this FlatPattern
The attempted operation did not produce a meaningful result. Try with different inputs.
I have a sheet metal part where I selected an incorrect edge when creating flanges, is there an easy way to deselect the edge? I can add edges and I can select the glyph for a specific edge to edit it, but short of deleating the feature and starting over I have not found a good way of deselecting an edge.
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium