I need to add weight to my parts list and notes for both parts and assy. Is there a way to get the weight parsed out from the model without the "lbsmass", just the pounds number no nomenclature I have a couple of other questions on parts list customization also. Also are these better questions for the customization group?
View 2 RepliesI've been looking for a solution to remove the unit string ie Lbs, g, kg from the value given from a 'Mass' value in a text string.
As you may all know, creating text and having a 'physical property - mass' value...the unit string is there...
Lots of people on here have the problem...no-one has got a solution.
Until now...
Basically...open the part you need to get the mass property of in your text string.
Follow the instructions on this webpage...this is the first part...
[URL]
Basically, this creates a Mass property value in the parameters table that you can call on as a text parameter.
It's similar to the custom iproperty model - mass but NOT the same.
Once you have done this, you can go to the drawing of the part and create a text string in the drawing and call it up as shown in this procedure. BUT it still has the unit string.
Here's the best bit that you want to know...
To get RID of the unit string...open up the part again from the drawing...click on the parameter icon...find the user parameter...in the Nominal value column, right click on the value and you get a pop-up that gives you 3 options...
Custom Property Format, Make Multi Value & Delete Parameter.
Click on Custom Property Format.
The pop-up window comes up...showing you the property type...in my case...the 4 left columns read Text, g (grams), Format & Precision...
On the right hand side I have a Preview of the text...then 3 check boxes...Units string, Leading Zero's, Trailing Zero's.
Units string is checked.
Uncheck it.
Close it...Save your part...go back to the drawing and hey presto!...the text now shows the weight you require as a straight value...no units!
I am now looking to work with custom iProperties that will populate our company's new BOM standard. I have not done much with regards to customizing a BOM (I've always used the generic fields). Now my boss has come to me and wants to use the following headings for our BOM....
REF ID, QTY. , DESCRIPTION, SHAPE, SIZE, LENGTH, MASS, TOTAL LENGTH, TOTAL MASS, COMMENTS, REF. DWG.
REV., REV. DATE
While I understand some of these fields will require the user to manually type information in (Comments and Ref. Dwg.) The others, from my understanding, can come straight from iProperties or Parameters. I am running INV Pro 2013.
Is there a way to customize the BOM columns so that Inventor remembers which columns I need? I know that I can add in the file name column etc. but I use the same columns over and over. I find myself in every assembly adding these columns in.
Autodesk Inventor Professional 2010
I'm trying to do a customization of the Bom structure to obtain a new custom column "Qty*x" (where "X" is a number).
I need this because in my order I have multiples of these items.
I have been working on creating custom content center families that will populate our company's part numbers and descriptions into the browser and drawing BOM. I have been quite successful in this except with the material. I've created custom materials for the fasteners that have the specified strengths and finishes per the fastener. By doing this I've created a different problem.
How can I create a custom property that will insert a specified value for material into the BOM? I've tried to change the link for Project.Material and then the part inserts as Inventor's default. I don't think creating individual material styles for each fastener is a viable one since I'll end up with duplicate style names.
IV 2012
Running on:
Windows 7 64 bit
12 GB Ram
Intel Xeon processer
I have created a drawing from the parametric model assembly where i have clevis, lug plate and pin arrgt.
the model has been generated using the input excel spreadsheet where i have given the inputs like clevis thk, lug thk,pin dia etc.,
while creating the drawing partlist i have included the column of clevis thk, lug thk etc., using the iproperty, but these columns are coming separately, i just want the thk of clevis and lug in the same column so that i will make Bom for the assembly.
How to get the parametric inputs in the same column of the patlist in drawing.
Earlier I`ve used a simple code from Rob Cohee to update the title blocks and it works like a charm, however, now I would like to try to kick it up a notch.
If (ThisDrawing.ModelDocument Is Nothing) Then ReturnmodelName = IO.Path.GetFileName(ThisDrawing.ModelDocument.FullFileName)iProperties.Value("Project", "Part Number") = iProperties.Value(modelName, "Project", "Part Number")iProperties.Value("Custom", "Client") = iProperties.Value(modelName, "Custom", "Client")
I`m working with several similar projects where the Inventor models and IDW`s is copied from one project to another. A typical project can consist of 50-75 drawings and the only properties needed to change is Client, project number and drawing number (consisting of the project number and a suffix, ex 123456789-125).
I would like to try to make an .ini file with these 3 properties in the root of the project folder so they can be changed and updated easily.
I've been forcing myself to accumulate to the new marking menu and gestures system. I'm starting to get used enough to them to see that it's really worth it.
I've found that the defaults are crap for what I do in IV, which is fine because I can customize it to whatever I do use.
However, when I RMB on a component pattern it displays a unique menu for which there appears to be no option for under customization. I'd really like to replace the craptastic useless options with things that I actually use.
By the way, why does AutoDesk neglect component patterns so much?
Question regarding view labels in drawings.
I want to change the appearance of the view label to look like attached snap shot. Is this possible? I have looked through the inventor settings but cant find any options.
As a possible solution I can always create intelligent symbols which update with the drawing (like the standard view labels) but before I begin creating these I wanted to check if there was any other way?
I want to run a macro from a keyboard shortcut like I have been doing in the last several releases of Inventor. I can set the shortcut and it works. If I close/restart Inventor, the shortcut is lost.
See video here. [URL] ..........
Inventor 2012, sp1
Inventor Pro 2010, XP Pro SP3, Compaq nw9440 laptop with NVIDIA FX 1500 VIDEO. why tools added to Quick Access Toolbar will disappear. they were here yesterday, gone today. I've reset them to see if I can duplicate the problem.
View 6 Replies View RelatedI'm starting to develop some customization for Inventor, and I need to decide whether to use VBA, .net, addin, plugin, or what else.According to this post .net is easier to use than VBA: URL....
I did a quick test and I found out that with VBA is much easier to use than .net: you can edit the source code while debugging, you don't need to compile and install anything, everything seems to work much smoother.Do I risk to find out that VBA has problems later in the development?
Where can I find documentation with comparison between the different customization techniques?
The Marking Menu of 2012 so far is a big brake for me.
I wish I can make some alterations but I did not find in this huge variety of possibilities
the option to alter the context menu of the Sketch.
I am in Sketch. I drawing the line. I want to quit. I do right click and have the menu. the name and probably the sub name of that menu. I cannot find it at all in the Customization list. I wish at least to locate the Escape to bottom. Did not find also the option to turn the Marking menu off.
I'd like to customize the way our section marker terminators look. More like an architactual style drawing.
I'd also like to add the sheet number that the section is cut from to the section view label.
As far as I can tell, this propertie is not available for insertion in the view lable. Is there a way to make it available?
The need for these changes come from larger drawing sets were the section is cut on one sheet and shown on another. We'd like to link the sheet numbers in both the section marker terminator and view label.
We are trying to relate to the floor how many pieces of HW should go in partiular places.
The balloon with HW count, unfortunately, gives only overall quantity which is less then useful.
I describe my problem in the graphics area attached.
Should be easy, I guess, but, so far, wecould not figure out the best way of dealing with it rather than we are using now.
How can I see the mass of a solid, or if it's not possible, at least the volume.
View 1 Replies View RelatedI was checking my prints and noticed that the mass for the assembly was not shown correctly. The mass for each component is correct, but the mass for the assembly is less than the total mass of the parts..... how can that be?
Watch this video. The mass for my assembly is reported from iProperties as 10 lbs, but the mass for one of the parts is 60lbs. I would expect the mass for the assembly to be at least 60 lbs, but it is not. I tried a "Rebuild All" and an "Update Mass" on my assembly, but that did not fix it (30 sec mark in the video).
This assembly is part of a much larger assembly (around 35,000 parts). There are several more assemblies doing this and I need to get the mass correct.
I am using 2013 x64, SP2.
I have an assembly that i need to know the mass of, easy enough, however the assembly needs to be weighed without some of the parts in it. I hought i could simply uncheck "enabled" of the unwanted parts and re check the mass, however it does not change. Any solution besides adding the wanted parts individually?
View 6 Replies View Related have one assy comprising of a valve, made in steel, an actuator made in aluminum, total weight combined is 36 kg.
I make this assy a derived ipt.. i have tried all the output options, single solid, multy solid and the weight is not the same.. since its a new ipt has its own material, ok makes sense.. .. So i use composite, i get the correct weight (yay), but now i cant turn the visibility off on the 2d drawing, in certain pipe spool view representations.
What is the correct procedure for turning multi material assys into an ipt.. to get the correct weights and get the drawings to work properly?
How to set the mass calculation accuracy to 'Very High' when doing calculations in iLogic.
I asked for the iLogic equivalent to the VBA term:
' Set the accuracy to VeryHigh.
oMassProps.Accuracy = k_VeryHigh
and was provided with:
oMassProps.Accuracy = 24580 'k_VeryHigh=24580
However, I believe that the value 24580 is actually equivalent to k_Medium. Confirm the iLogic equivalent value of k_VeryHigh.
Original post: [URL].......
In assembly file - BOM - mass property, parts with the same name (part number) i get "VARIES"..Parts have a little bit different mass - 0,167kg and 0,168kg. I do not want to have different part number.
So, i'm going to do something like this in iLogic :
iProperties.MassOfComponent("fi_N1:1")=Round(iProperties.MassOfComponent("fi_N1:1"),1)
it works but is there any way to do it for all parts (hundreds) automagically in the loop (iLogic or VB) ?
I have recently made a bucket for chain (linked) and was looking to put the chain in the bucket for visual purposes and to see if the capacity of the bucket is correct.
I can get the chain linked together, however when rotated round it passes through another piece of chain.
Is there a way in inventor to tell a part/assembly of it’s physical/mass properties? I know you can make something mild steel and get weight etc, however if not constrained it still passes through as if it’s a ghost.
I have added the mass properties and I do not want the lbmass behind it. How do I get rid of it?
View 5 Replies View Relatedi found same topics as my, but i didnt find solution.
Is there any way for mass convert idw files (not same format - A4,A3,A2, ...) to pdf ?
I tried task manager, but i dont have some account for it.
I'm having trouble getting mass properties of an assembly to display in an .idw. I've tried it 2 diffent ways, custom properties-model "Totalmass" where I type the mass and physical properties-model "mass" where it's automatic with update.. Nothing shows, not even N/A, but in another idw (different assembly) it works. Both text boxes are saved within a sketch that is part of a template. Both idw's use the same template. If I place text on the drawing it self it works.
IV 2012
Vault Collaboration 2012
To get net weight of my parts i have one template that uses the volume x density and to get the gross weight I use the real dimensions of the item (a rectangular plate without any cutting, e.g.) and then calculate x density, this way i can get both weights, and how in the most of times I need the gross, I overwrite the MASS PROPERTIES of each part with my gross weight. It works fine because all the assemblies sum the MASS of each part (that is over writed by the gross weight).
Now my problem:
In many cases when I need to use the same part many times with just a few of different details, instead of copy the part and change it, I use the same part, and in the IAM I use one feature to make this part different (like a chamber, small extrudes or even holes). But now I realized when I do this (feature in the IAM), it doesn't sum all the MASS properties of each individual part anymore ... it recalculate all the mass with the new IAM volume (with all the features)...so, in my BOM I got all the parts with the correct gross weight, but my total mass comes with the NET weight (and considering that I need the GROSS, i got the wrong mass).
Is there a way to change the way that inventor overwrite this mass in the assemblies ? with Ilogic, or even some Inventor's option ?
Is there any way to force an update of mass property values of a component from within an iLogic routine?
I am trying to produce a calibration chart showing the volumes of an irregular shaped object by taking incremental slices off the component and accessing the "volume" of the remaining portion, then writing the the results to an external file - All from within a "For - Next" loop.
The main routine works O.K. but the resultant chart only shows the original starting volume for each slice instead of the required reducing volumes.
I am a novice with iLogic and can only assume that I must somehow "update" the mass properties of the sliced object before reading its new volume on each pass.
How can see visually the center mass of a part or assembly?
When I'm checking in the Iprop., I see the center of gravity coordinates, but it there a way to "see" it (some visual representation)
Inventor 2012 Pro.
I7 workstation
We want to obtain the center of mass of two or more subassemblies within an assembly. How to do it? The subassemblies may or may not be connected to each other directly.
View 9 Replies View RelatedMy company recently installed Inventor 2013. In previous versions we used a part with negative density similar to seawater to calculate submerged weight and CoG.
In IV 2013, it seems that the ability to calculate negative mass is not longer available.
This is how it worked in pre 2013 IV, when I could specify a negative density.
What I have is a spool made of steel. This spool is modelled as an iAssembly with four configurations:
-In air, empty
-In air, filled with glycol
-Submerged, empty
-Submerged, filled with Glycol
For this example, I now need three parts:
-Steel Pipe
-Glycol derived from the inside volume the pipe
-Seawater buoyancy derived from the outside volume of the pipe.
Each part has its own density, and the assembly weight and CoG correspond to the assembly configuration (with or without glycol) and environment (in air or submerged).
The seawater buoyancy represents the water displaced by the total spool assembly, regardless of the contents. To achieve correct weight in the submerged state, the buoyancy material has to have a negative density.
I do not want to make any of the mass parameters static, and I also fear that the CoG might not be updated correctly when using that method.
As I no longer can define a negative density, any optional method to achieve this without overriding the mass value.
Autodesk Product Design Suite 2013 SP1
Win 7 Enterprise 64bit
Intel Xeon CPU E3-1240 V2 @ 3.40GHz
16Gb Ram
Nvidia Quadro 2000