I would like to know how I can find a dimension that's created with the command (with the internal command name) "Create3DLinearDimension".
This command is used to create a linear dimension on a view that has the default dimension type set to "True".
So autodesk has added linear symmetrical dimensions. How about adding the double arrowhead that should be on the trailing end
or even better...how about expose the code so we can create custom arrowheads . Also posted on customization board:-
[URL].......
I have a STEP file which is of a part similar to the rudder of a boat or an oar blade but twisted at the end, and I have to draw the split line to match the profile of the blade. I imagine I have to use a 3D sketch because of the twist and we are guessing that the split line will run down the apex of the blade, but I don't know how to get the 3D sketch to "stick" to the apex (there is no real apex as it's curved).
View 5 Replies View RelatedI have a problem regarding linear dimensions on 3D blocks.
I create a set of 3D blocks and add linear dimensions to these in paperspace. When I want to edit a block the line origin of the linear dimension loses its original set point and I have to spend a lot of time changing the annotations in paperspace.
Am I using the wrong type of annotative dimensions or have I chosen the wrong angle to add dimensions to my blocks altogether?
I am using AutoCAD 2011. When I create a radius dimension on the inside of an arc, and I place the dimension beyond the center point of the arc, AutoCAD automatically draws an extension to the arc and points my radius dimension leader to the outside of this extension, rather than to the inside of the original arc.
I don't really like this. I prefer for my demension leader to point to the inside of the original arc. I can get exactly what I want by going into "Properties" for the radius dimension and turning the "Ext Line" property off.
Rather than having to do this every time, I'd like to create a dimension style that would give me this functionality all of the time. When I try to modify my dimension style, I see that there are just two parameters for Suppress Ext Line 1 and Suppress Ext Line 2. These seem to apply to both linear dimensions and radial dimensions. Is there anything I can do to suppress the extension line for radial dimensions only and not linear dimensions?
How do you remove singular dimensions from within a string of linear dimensions?
At the moment I cannot delete individual dimensions and am required to delete all dimensions in that string and start again.
I'm trying to reposition dimensions in a drawing through the API. The output of my code seems to indicate the method is working, but after it runs the drawing is unchanged. Here's the code (in VBA):
Dim oDoc As DrawingDocument
Set oDoc = ThisApplication.ActiveDocument
Dim oSheet As Sheet
Set oSheet = oDoc.Sheets.Item(1)
Dim oLdim As LinearGeneralDimension
Dim oLeaderNote As LeaderNote
Dim oDimLine As LineSegment2d ' Dimension Line
Dim oStartPt As Point2d ' Dimension Line Start Point
Dim oEndPt As Point2d ' Dimension Line End Point
[code]....
Looks like it moved my vertical dimension left, but it doesn't actually do anything. Is this not a viable method for repositioning a dimension?
I created a sketch then tried to retrieve dimensions in a drawing from the sketch. When I used the retrieve function, no dimensions appeared. I made sure that the box in the Application Options under the Tools tab was checked for retrieving all dimensions upon placement. I have tried numerous ways to retrieve the dimensions, and while I can place them manually, I really need to be able to retrieve all at once as seen on the sketch.
I have been able to use the retrieve function before on files that I downloaded from a website so I know to use the function.
I'm attaching a file which I am having trouble retrieving dimensions. I am using Inventor 2013 educational version.
I'd like to take a set of ordinate dimensions and multiply all the values by 10. Is this possible, without overriding the values and making them static?
The reason I'm asking is because I'm making a flat layout sketch for pockets around a drum. So imagine taking a drum and rolling it out flat. In the direction along the drum I drew it as 1" = 1" and for the circumfrence direction I did 1" = 10° so I don't have sketch that is 13" x 360". So I need to scale the dimensions in 1 direction up by 10.
I got a new computer recently and installed Inventor 11. I found I could not change the drawing dimensions (It chanced in the Edit Box and shown the changes in the dimensions, but after click "OK", the Edit Box closed and the dimension did not change).
I remember there were the similar problems before and I installed KB918118 fixed it. So I tried to install KB918118. But my computer shown a message saying my computer system is newer and do not need the KB918118 update.
I am wondering how best to apply drawing dimensions to a view. I am using VBA (Inventor 2010 x64) to modify a template skeletal assembly and save it. I have succeeded at generating the models, drawings, and drawing views, but have hit a wall when I attempt to automate the process of applying drawing dimensions.
I attempted to use GeneralDimensions.Retrieve with the DimensionsToRetrieve parameter, as I wish to retrieve only a few dimensions. My testing, however, indicated (and the helpfile confirmed) that the DimensionsToRetrieve parameter only work if the DimensionConstraint objects belong to a drawing sketch, and I'm retrieving dimensionconstraints from a model sketch. It appears to me that I will have to retrieve all dimensions and then somehow delete the unnecessary ones. This seems unusual to me--is there a better way? Can I, for example, retrieve a single dimensionconstraint at a time from the model rather than all of them at once? Perhaps its suitable applying drawing dimensions without retrieving them from the model?
I got a new computer recently and installed Inventor 11. I found I could not change the drawing dimensions (It chanced in the Edit Box and shown the changes in the dimensions, but after click "OK", the Edit Box closed and the dimension did not change). I remember there were the similar problems before and I installed KB918118 fixed it. So I tried to install KB918118. But my computer shown a message saying my computer system is newer and do not need the KB918118 update.
View 4 Replies View RelatedI use parametric base-model which automatically generates drawing (look "Pic1"). I change parameters I need and new drawing is generated (scale stays the same). However, dimensions on new drawing are displayed in random way (look "Pic2"). Is there a way (iLogic, VBA or smth els) to fix/link dimensins so - that they could stay in an appropriate way (space between dimensions, space between dimension and edge, dimension is centered on line with arrows) when the model size is changed (in this example I have changed the base diameter from 830 to 1280)?
Function "Arrange dimension" does not solve the problem!
I have an asssembly stack and I have a known bending moment at a given place (ie the datum). I want then to create a drawing of this stack up and show the bending moments at known locations beside the relative dimension.
Now I can do this manually no problem...but I would like this drawing to update automatically. ie the stack up height(s) change and i want the bending moment figure to update accordingly.l
Is there a way to do this with drawing dimensions? ie dimensions created in drawing mode?
One of the drafters I work with has been having an intermittent problem with Inventor 14 deleting dimensions and notes when he prints a .idw to a .pdf. The problem first popped up when we transitioned to 14 from 12. It only happens once out of every 2 dozen or so prints and is usually caught on the redlines, but it has been overlooked once already requiring the part to be remachined at cost to our employer. No one else in our office has had the problem and it continued to happen after a reinstall; which leads me to think it's some hardware issue.
Included is a screenshot of his system information. We're running Synergis Adept file management software, that may be pertinent as well.
Apparently I can't edit model dimensions from a drawing because i did not select this option when i installed inventor 2010.
View 9 Replies View RelatedI am trying to figure out how to properly define the dimensions of an exponential curve in a drawing to make it easiest to have the piece machined.
I am starting to wonder if inventor refers to this type of curve as something else entirely, as well. Since an exponential curve is like the shape of an airplane wing and doesn't have a "consistent" angle.
How can I round drawing dimensions modulo five, keeping them dynamic?
If I have length equals 203, I can get rounded length 205. Besides, having 206 - getting 210.
If in model length changes to 313 - I'll get 315, when 316 - 320.
Probably, I should override value, using VBA. Are there other abilities?
I know you can obviously set the tolerance in the styles to round to the nearest 1/16 or 1/32, but is there a way to make it always round a dimension up instead of to the nearest? IV2012
Windows XP SP3 32-bit
Intel Core 2 Duo 6400 @ 2.13 GHz
Nvidia Quadro FX 3450/4000 SDI 256MB Vram
2 GB Ram
160GB HDD
While working with an Inventor 2013 *.idw some of the dimension lines, extension lines, and learders became invisible, even though you can still see the dimension values and even the arrow heads of the no-show dimensions. Even when printed, the same lines are not there. 2013 Glitch?
View 9 Replies View RelatedI want to retrieve dimensions in a drawing with ilogic. I found some code but how to translate it into a ilogic code.
I always use assembly models in these drawing and all the parameters have unique names. So in my drawing i want to retrieve some specific dimensions in a view.
Is it possible to link the dimensions in my .idw to the table in the upper left corner? I want the information in the table to reflect what is in the drawing.
I'm using Inventor 2012
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
Recently when I have placed a view of an assembly into an idw drawing, then try to dimension distances between parts it gives me strange looking dimensions, or no dimensions at all. It looks as though the dimensions are going from the edges of each part at different angles, when I want them to be parallel to the view. I just want the dimension from a line to a line in that view as though it is 2d, but it is acting like it is still in 3d. I do not know if their is a setting that will change this or not.
I attached a screen shot of what the dimensions look like.
Is it possible to use the Measure.ExtentsLength in a drawing to get model dimensions?
What I am trying to do is get the overall dimensions of the model and place them in a sketch block in the drawings so our machinist can easily reference the stock material. I can't figure out how to get the overall model dimensions.
Windows 7 x64 -24 GB Ram
Intel i7-3840QM @ 2.8GHz
nVidia Quadro K5000M - 4GB
Inv 2013 SP2
Vault Collaboration 2013 Update1
After looking thru the api, i'm finding it hard to get a list of orphaned dimensions.
I can get a list of all the dimensions...easy.
I've basically deleted a part from the assembly and now want to remove that dimension in a section view on the drawing document.
But looking / comparing the properties of a non-orphaned vs an orphaned shows nothing.
Is there an orphaned list?
Is there a color override switch somewhere?
Or can I somehow get the object that the dimension is trying to reference and check to see if it is valid or has a valid file reference...or something?
I have a automated ilogic model that is then used within a 2D drawing, this 2D drawing then has dimensions on it referenced to the the model.
This model changes in its length the dimension associated with its length then changes but the dimension text then goes outside of the dimension boundary (does not stay central). Is there any code that can scan the dimensions and in effect tidy them up?
I found that I can right click a dimension in a drawing and select "Move Dimension" which then prompts me to select an alternative view in which I want the dimension placed. Is it possible to control-click multiple dimensions once to do this all in one fell swoop (e.g. I decided my view is too busy and want to move dimensions to a newly created detail view of that area)?
I'm using Inventor 2010
I'm in sketch mode and my drawing dimensions are all in decimal format. How do I change that to a fractional format?
I thought it would be in the styles editor, but when I open that up, I don't see ANY dimension style listed (see picture). I also tried right clicking the actual dimension to view the properties, but that only lets me change the decimal precision (also attached). The help file mentioned the "ANNOTATE" tab, but I don't even have that tab on my ribbon so I'm guessing it's unique to autocad?
Is there any way I can make exploded dimensions in an old drawing become live dimensions again.
View 3 Replies View RelatedI'm trying to write a VBA macro (for Inventor 2010) that would have to work on drawing .idw files that are generated from a given component.So when I have an open assembly document, I want to go through all component occurences and work with the associated drawing.
There's a built in command in Inventor for that, in the context menu, something like "Open drawing" (mine is german, so not sure how it's called in english), which does this. It opens the drawing of the given part. From this I assumed, there must be a reference within each part, that points to the referencing drawing.
But I'm not able to find this information anywhere within the properties/objects of any component.how or where can I get this information out of the components?
how to identify the model associated with a particular PL on a drawing. I'm able to find a PL and write to the header which is cool. But I'm trying to determine the model associated with the BOM pipline so I can get it's P/N iproperty and write that to the PL header.
View 2 Replies View Related