I have done a new Title Block in our drawing templates.
It only works in New drawings if I open an old drawing I must "Copy/paste" the new Title Block into the browser to the left But I want all our old drawings to use the new Title Block.
Is there a way to have the new Title as default on all old drawings?
Is there a way to add the sheet name to the title block of drawings with a variable?
I can add the sheet number, revision and size but not the name. Why not?
I do a lot of work where I start with a full assembly drawing, then make more drawings for the individual parts. Is there a way to link the title block parameters in the part drawings to the title block in the full assembly drawing? The only way I found was to link the parts together and then grab the info for the drawings off of the parts, but if I'm implementing this in a template used by others I want them to still be able to just fill in the blank on the assembly drawing to make it work.
I was able to get iProperties to show parameter buttons, but I haven't seen any way to link to other files or anything like that.
I'm having some difficulty in deciding how to go about creating a title block for my drawings. I have attempted to create the title block with Document fields from the drawing properties custom properties tab, and creating the same fields with information from the Sheet / Sheet Set fields. Both title blocks used attributes inside the block to house the fields, and both were .dwt files.
Is there a way to take the properties from the .dwt drawing into a newly created drawing, or is there a way to link custom sheet set properties with a newly created sheet set? The main goal is to not have the user manually input multiple custom fields either in the drawing properties or the sheet set manager of the new drawing.
The title blocks that we use have prompted entries in them and I would like to find a way using iLogic to copy the entries from one title block to another within the same drawing; i.e.. if the user decides to change from an A2 to A1 drawing.
I already have an iLogic rule which allows the user to change the active border, title block and sheet size based on a form selection but would like it to capture the prompted entries already entered and re-use them after the change.
I need to insert two different (separate) title blocks into my idw drawings so both show on the drawing. One is the real Title block, and one is a Revision History block. I have listed them as Title blocks under Drawing Resources, but Inventor won't allow me to insert both. Is there any way round this?
I do not want the Revision History block as a Symbol.
Inventor 2011; MS Windows 7-64; i5-2500; 8Gb; GF550Ti.
How can I customize the title block where it says Drawn, Checked and approved?
I want the dates with initials to place automatically. However, I want the date of approval and checked to be 2-5 days after the drawn date. (using Inventor pro. 2012)
I am trying to replace the title block of the first sheet of the active drawing via C#. I currently am receiving the following error on the last line of The parameter is incorrect. (Exception from HRESULT: 0x80070057 (E_INVALIDARG)).
Why the code below is throwing this error? I have tried multiple variations of the code below to no avail and I'm sure this is something minor that I am overlooking. The title block definition under Drawing Resources is replaced with no errors, the title block on Sheet 1 is deleted just fine, but I can't seem to add a Title Block back in!
How Documents are defined:
Inventor._DrawingDocument oDoc = getDoc();Inventor.DrawingDocument sourceDoc =(Drawing Document) instance.Documents. OpenWith Options(sPath, options, false); Find, copy, replace: TitleBlockDefinition tBlock = sourceDoc.TitleBlockDefinitions[blockList.SelectedItem.ToString()]; TitleBlockDefinition newBlock = tBlock.CopyTo(oDoc, true); oDoc.Sheets[1].TitleBlock.Delete(); oDoc.Sheets[1].AddTitleBlock(newBlock);
I am trying to include the weight for all components in assembly BOM as well as calculated overall weight in TB, but there are no available property to choose from in the drop-down list.
View 2 Replies View RelatedI've created the user parameters and they get the information I need by the rules in illogic and also added as custom properties, but when I try to put them on the title block they don't retrieve the information.
View 9 Replies View RelatedI've created the user parameters and they get the information I need by the rules in illogic and also added as custom properties, but when I try to put them on the title block they don't retrieve the information.
View 1 Replies View RelatedI have added the mass properties and I do not want the lbmass behind it. How do I get rid of it?
View 5 Replies View RelatedMalfunctioning Title Block Macro in Inventor 2014? The script is attached. I think there is a problem with datums. I have switched to a new computer and installed Inventor 2014 on it. The macro worked with my old computer and Inventor 2013. This is a .ivb-file, not a .txt-file. Please change that before you test it.
View 8 Replies View RelatedI have a cutom title block that automaticly places material, status, stock number etc. of the component in the drawing sheet, but I am stumped as to placing the quantity automatically. I have defaulted to using a prompted entry, but that is prone to errors.
View 9 Replies View RelatedI have text in my title block that references part properties. If I have several different part and assembly base views on a sheet, how do I control which one the title block references? It defaults to the first one that was placed. I am using 2011 Pro.
View 1 Replies View RelatedIs there an add in or something for faster type in the title block in a drawing? Name, title etc?
Right now the author and date are automatically but when i save the file to for example to "D1234 hammer" it becomes the part number.
I have to edit the title.
I want to save the file to "D1234 hammer" and the partnumber to be "D1234" and title "hammer".
IS there a add-in that I type the title and name and its auto fill the title block? Or do I have to create a custom title block so the drawing can understand to only to take the numbers from <part name> and the letters becomes <title>?
We are going to be making a new title block and I have been looking at ways to get the new title block into the old drawings. It looks like the Inventor Drawing and Resource Wizard is the way to go.
The steps seem pretty straight forward and simple but I am not getting the correct results. For the source drawing I select my new title block and leave the boxes for borders, my new title block name, and sketched symbols checked. I then pick my drawing I want to get the new title block in. On the last step I can select Yes or No and get the same results. When I reopen Inventor and the drawing it still has the old title block in it.
Is there a way to change a title block? After finishing all the dimensioning and details I realized I used the wrong title block.
View 3 Replies View RelatedI use two different measuring system IMPERIAL and METRIC.
What I want is to be able tell at a glance, by having different color border and Title-block Text is which one of the system of units I'm using
So what I'm wanting to do is create a Metric Sheet template with on color, Border, Title Block Text and a different color for the Imperial.
I've tried changing the color using the Style Center but that affects both templates, I've tried editing the title-block text saving the template but on opening it has changed back to the defaults set in the style settings and dose not hold those that I set.
What I don't what to be doing is changing them after opening, as at some stage I'll forget.
So, I am trying to add a copyright year to a title block in a drawing template file used through out my company. I want to base the year off of the creation date property - I am trying to find a way to truncate this property such that only the year is displayed. Ideally, any time the creation date property is changed, the copyright year will also update.
We are currently running Inventor 2010.Normally, I would just write an iLogic rule with an event trigger, but this would require everyone to install the iLogic addin which just won't happen.
Even easier, I could make a custom iProperty and just have people manually type in the year when they start a new drawing - this will be worst case scenario as a ton of people will forget and I'll just make more work for myself.I also have VBA code which is pretty simple:
Public Sub SetYear()
Dim oDoc As Document
Set oDoc = ThisApplication.ActiveDocument
Dim customPropSet, customPropSet2 As PropertySet
Set customPropSet2 = oDoc.PropertySets.Item("Design Tracking Properties")
[code]....
The issue would be getting this VBA code to trigger and to "stick" to the template file.I can just as easily write this code in VB.NET or C#, and go through the hassle of creating an add-in, but again, how would I get it to trigger and stick to the template file.
I have a customized title block that I created in an idw. I want to make that block available for all drawings for different projects. How do I do that?
View 3 Replies View RelatedEarlier I`ve used a simple code from Rob Cohee to update the title blocks and it works like a charm, however, now I would like to try to kick it up a notch.
If (ThisDrawing.ModelDocument Is Nothing) Then ReturnmodelName = IO.Path.GetFileName(ThisDrawing.ModelDocument.FullFileName)iProperties.Value("Project", "Part Number") = iProperties.Value(modelName, "Project", "Part Number")iProperties.Value("Custom", "Client") = iProperties.Value(modelName, "Custom", "Client")
I`m working with several similar projects where the Inventor models and IDW`s is copied from one project to another. A typical project can consist of 50-75 drawings and the only properties needed to change is Client, project number and drawing number (consisting of the project number and a suffix, ex 123456789-125).
I would like to try to make an .ini file with these 3 properties in the root of the project folder so they can be changed and updated easily.
Below is a code I managed to scramble together to display the unit used in the drawing template. The units are selected once the drawing is opened based the Standards ANSI and ANSI-mm from the styles library.
The code displays the units used in template as a custom iproperty called "drawingUNITS". This code works great however, I would like it if possible to be more clearer to the shop guys looking at the drawings.
I would the result to be
ANSI = Imperial (or inches) and ANSI-mm = Metric
is there somewhere in the code provided that I can get my desired result?
' To use this rule, create a Text parameter named Standard in the drawing.' Assign it values such as:
' ANSI' ANSI-mmdoc = ThisDoc.DocumentcustomPropertySet = doc.PropertySets.Item("Inventor User Defined Properties") 'Make sure drawingUNITS property existsTry prop = customPropertySet.Item("drawingUNITS")Catch 'Assume error means not found customPropertySet.Add("", "drawingUNITS")End TryDim drawingDoc as DrawingDocument = ThisDoc.DocumentFor Each standardX In [code].......
I have created a custom title block and border for one of the automotive manufacturers since I need to submit all their drawings in the standard border and title block format. The border is quite broad, so when I insert the new title block, it overlaps the border slightly. I need to try and find the setting to control the exact point at which the title block is positioned when inserted into a drawing.
Windows 7 Pro (X64)
Intel(R) core (TM) i7-2600 CPU @ 3.40GHz
16.0 GB RAM
Nvidia Quadro 600
Autodesk Inventor 2013 Professional Ultimate Design Suite
I am using 2013 Inventor.My company uses the .dwg file extension instead of .idw (if that makes a difference).When I make a new .dwg file and insert an .ipt file for my first base drawing ..The material field of the .dwg Title Block is populated.This is something I would like to avoid.When I open iProps in the .ipt drawing and go to the Physical/Material Tab don’t seem to have the option to display a blank (no information) in the material field in the Title Block.The closest I can come to this is to choose Generic, which looks kind of odd.
My company chooses to give all material specs in a note displayed on the drawing.In case of a material change at some point, I do NOT want to have to change the note on the drawing AS WELL AS the Material information in the .ipt iProps.The reason is that, sooner or later, I’ll forget to change both(which will lead to confusion) and possibility lead to making junk parts (made of the wrong material) which will then have to be thrown away (at perhaps a major loss).
I've argued this repeatedly with the powers that be at my small company and they're set on some old methods that I'm trying to figure out how to make happen.
We often have weldments where we do an assembled view on page 1 and balloon it and have a parts list. Pages 2-4 will be the details of the welded parts. On page 1, I bring in the "Title" and "Subject" fields from the assembly iProperties.
Here's the tricky part. On pages 2+, I don't want to bring in those two fields, I want to bring in something different. Is it possible to differentiate like that?
Second part of the question: is there a way to pull the balloon item number from page 1 into a field somewhere on following pages? For example: page 3 may show the details for "item 2". Can I bring the value of that balloon (item 2) into page 3 somehow?
I am trying put drawing numbers on my drawings. The drawing number is "019-02-00038-x" where "x" is the page number in the set of drawings. How do I set this up? Every time I try to change "x" it changes it for the entire set of drawings.
I'm working with Inventor 2014.
I've customized the title-block template by changing a few of the default texts and by adding a graphic image.I know from other post here that when the new template is created and then used the graphic needs to have pointer set etc set a the time of creation of the new template, I've done all that and it works fine.
However there are two points :-
1) When a new drawing created with my template then saved as a IDW is the graphic image then embedded in that IDW or referenced each time the file is opened?
2) If I upload these IDW files, as created as above to a web site or transfer to another machine do I need that template file and image to be on that other machine and/or do I need to upload the template and graphic graphic files with that/those IDW, IPT, IAM files so that when some one else opens these IDW files that graphic is displayed?
Inventor 2013 Pro
I am trying to get the scale of the base view in my titleblock. I have searched, the conclusion that as of Inventor 2012, this still can not be accomplished without add-ons?
View 9 Replies View RelatedIn the ANSI-large, the default title block in the ANSI drawing template, when i edit the title block i see green lines which might use for aligning text. they disappear when i finish editing.
They are on a layer that's: By Standard (title ANSI). The rest of the lines are black and are on the title ANSI layer. What's this By Standard prefix? What are they and how to make them?
Creating a custom title block in innventor seems to be straight foward however when I save the new title block it offsets from the sheet, up and to the right. How do I get the title block to line up with the sheet
View 3 Replies View Related
