AutoCAD Civil 3D :: Transition Between Subassemblies - Show Up In Cross Sections
Jun 25, 2012
Along my corridor I have different assemblies I used. My sidewalk is curb side in some locations and in different locations there is a boulevard between the curb and sidewalk. I want to transition between these different assemblies and I want that transition to show up in the cross sections I cut. Isn't there a way to tell Civil 3D to transition from one assembly to the next one as you could in Eagle Point?
View 9 Replies
ADVERTISEMENT
Nov 29, 2012
I have a fairly simple corridor, however, I had to modify the alignment, rebuild the corridor and resample cross-sections. Now my right daylight slope won't show up. It shows up in the section viewer, but not the cross-section. I had this problem once before and fixed it, but now I can't remember how I did...I have all targets, sections sampled match corridor sampling etc.
Civil 3D 2012 SP1
Windows 7
View 2 Replies
View Related
Mar 19, 2012
I've got a series of cross sections that show an existing and proposed scenario and I need to show the location of the site boundary on the (multiple) sections.
I tried making a feature line from the site boundary but all the feature lines get projected - how can I just get the site boundary to be shown?
View 1 Replies
View Related
May 1, 2012
I have created a road for a pit mine (which is unlike roads I have designed in the past). The road switched back towards itself and I need to daylight the cut slopes to show the limits of the mine/road cut. However, my cut/fill lines are not showing up in my cross-sections, but the plan view is showing the limits of excavation.
I assume this is because my limits are intersecting, from each of the roads, the upper and the lower. How can I get around this, or why are my cross-section lines not showing?
View 2 Replies
View Related
Oct 19, 2012
In a particular road project i need to show for all the cross sections, the coordinates (x,y) of the main points ( for example: daylight, etw and crown). I know that i can obtain it from reports->corridor but as far as i know, i must edit in excel and paste each PK info next to the correspondant cross section.
Is there a way more automatic raher than copy paste the report list?
View 9 Replies
View Related
Dec 5, 2006
Im using AutoCAD 2007.
I have done a land survey showing a top of bank - and the bottom of bank, which ive then contoured by using Carlson Survey (AutoCAD engined).
Im trying to draw cross sections through my model that would obviously show the level of the surface.
The bank lines and contour lines are polylines.
View 9 Replies
View Related
Oct 3, 2013
Is it possible in civil 3d to input a cross section of superelevation as parabolic rather than straight section in civil 3d. We are looking at a parabolic bend of 40 degrees.
View 6 Replies
View Related
Feb 25, 2013
I am working on a project for a park in which they are looking for a new access road and a parking lot. I created the road and sections for it, now im looking to get material cut/fill from the sections. I am having a tough time getting them to work. The only thing I can get to work is if i created a volume surface comparing my eg to my fg surface. That will give me a cut and fill material amount for my new road
What i am trying to get is the volume report for each sections, so i can get the cut/fill for each section. I have followed the tutorials and tried everything, but nothing seems to work. I created a surface from my corridor, and for some reason when i go to edit my materials, i cant add my proposed surface from my corridor to make the comparison from, and i think thats my problem. Everytime i go to create my volume report, i get all 0's.
View 7 Replies
View Related
Jan 3, 2013
When editing the Cross Section Styles the Horizontal Axis changes do not take affect. Vertical will work as entered.
See attached image.
I am changing under the Horizontal Axes tab, on the Section View Styles Menu.
View 7 Replies
View Related
Mar 29, 2013
I am trying to set up portrait cross sections. I can get my views to create a grid and such that look correct, however when putting them on sheets, it rotate the border, but also the modelspace. Are there certain settings in the sheet creation or the dwt file I need to review to do portrait sections?
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
View 2 Replies
View Related
Feb 29, 2012
I have created a drawing called xsec. I xrefed the corridor drawing into it and data shortcut the alignments in as well. I created sample lines and cut my cross sections in the drawing. Everything at this point looks fine.
The problem happens when I create a new drawing and xref the xsec into it. In this new drawing only the right side of my cross sections is showing up. I want to use this drawing for my sheet set rather than have a bunch of tabs in the xsec drawing.
View 1 Replies
View Related
Jul 18, 2013
had my cross sections ready to go all day, had to add points to my surface layer is all i did, now when i cut the sections they are all laying on top of one another.
View 6 Replies
View Related
Dec 19, 2013
In attached file the normal cross slope of secondary road(AB) is 2% Right to left (Right higher). and for primary road cross slope is 2% Left to Right (Left higher). I produced this junction using intersection wizard and cross slope of secondary road only starts changing from start of curb return to match the long slope of primary road. Is this possible to increase this transition lentgh on secondary road to create smooth contours.
View 3 Replies
View Related
May 16, 2012
I have an assembly that contains a basic lane tranisition with a retaining wall next to the road. I have created an alignment for the lane transition to follow but the wall stays in the same place. Shouldn't the wall move with the lane transition? The sub assembly are inserted connecting each other. what am I missing?
View 8 Replies
View Related
Dec 19, 2012
I've created sections and set up Materials List with Shapes Defined (Edit Material List.jpg) but the View Group Properties do not reflect this and have to be edited to suit.
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 2 Replies
View Related
Oct 10, 2012
I sampled my sections at 25 feet intervals, created my section view group and them plotted my cross section sheets. All look fine.My problem is that I need to include Station 21+17.40 and some other similar stations (in-between the 25 feet intervals) into my cross section sheets without deleting the existing Sample Line Group and Section View Group. Is there a way I can sample my desired additional sections and add them to the existing Sample Line Group and Section View Group and re-plotted my cross sections?
View 1 Replies
View Related
Feb 4, 2013
We want to show two surfaces, an existing ground and a proposed ground, on a cross section. When the proposed ground meets up with existing ground, it would be nice for the line to end. With just existing ground continuing on. The surface is data referenced, and I would like to not break either of them. I thought adding a surface mask would cause the proposed surface to stop at the mask, but that doesn't appear to be the case.
View 2 Replies
View Related
Jan 21, 2013
I have everything needed for plotting of cross sections. Alignment, profile, assembly.
The "Corridor Section Editor" shows everything as it should be. Existing Ground, Final Grade, Labeling, etc. When "Create Multiple Views" or "Create Section View" only existing Ground shows. All layers are on.
View 3 Replies
View Related
Jul 22, 2013
civil3d 2012. I'm trying to find out how to create cross sections from existing ones that i have in autocad file. I allready have read for the way with offsets points, but is there a way to make full cross sections from the allready drawned?Is it possible to convert the existing lines?
View 7 Replies
View Related
Feb 5, 2013
With reference to the picture attached, I am trying to find the overlapping area between two different cross-sections. I.e.the area of green minus the area of white.
The hard way to do it would be to sketch a closed polyline over the area I want but I have about 100 of these to do and more to come.
Windows 7 64-bit
Intel Core i7-3840QM 2.80GHz
NVIDIA Geforce GTX 680M 4GB
16GB RAM
View 5 Replies
View Related
Aug 7, 2012
I have a drawing with some cross sections of road showing the Proposed road surface and Existing ground surface. Now we have received a new ground surface and we have to supersede the old ground surfae with the new one. is there any way to swap the surface in the existing cross sections?
View 5 Replies
View Related
Feb 28, 2013
I have a corridor with 2 intersections. It is more or less like a main road with an off-ramp and an on-ramp, both on the same side, with a big triangle shape island in between them. It involves an existing road widening and a connection with another existing road. Since it is a real scenario, the intersections aren't perfect 90 degrees nor the offsets are constant.
Create Western intersection and change offset and curb return targets to design aligments.Create Eastern intersection and change offset and curb return targets to design alignments.Model the corridor as per design requirements.Due to design constraints, I ended up removing both intersections. I didn't delete all the offset and curb return alignments although they're not targeted on any region. Deleting this alignments seems to make C3D crash. the actual intersection definition hasn't been removed, as I read on other threads. I kept on getting a couple of error messages on Panorama Event Viewer every time I rebuild the corridor.
So, the problem comes when I try to output the cross sections from this nice looking corridor. They all look fine until they reach the intersection area. From the intersection onwards, the corridor is not displayed on any cross section. Even way passed the western intersection.
Why the corridor doesn't display on the cross sections passed the deleted intersections?I have a bad feeling that removing the intersection wasn't a good idea in the first place but it's too late now.
View 4 Replies
View Related
Nov 21, 2013
I am working on a project which has numerous existing conduits laid out on the site. The location of the services has be picked up by a surveyor on the surface at numerous location and provided as a 2D polyline. The lines are quite long with a large number of nodes.
I wanted to represent the conduits as say a 100mm pipe and locate it about 0.6m below the surface to get an idea of how it impacts my works.
I tried converting it to a network fails as there is >70 nodes. I really only need to see the conduit on the cross section as I will definately avoid it.
Is there a way to display 3D polylines in cross sections?
View 1 Replies
View Related
Nov 25, 2013
I have multiple surfaces representing topsoil, clay and types of bedrock, and an alignment set with sample lines and sections set. Trying to use the Compute Materials using material lists and the corresponding shape style to hatch between each surface something is going wrong. With all the display settings (Plan,Section,Profile,etc) set to by layer and on a created layer(not on 0). The shape area fill is set to solid. It will not display the hatch.
View 3 Replies
View Related
Apr 17, 2012
How do I get the cross sections to display a cut/fill value?
View 4 Replies
View Related
Jul 24, 2012
I am having an issue with the pipe networks drawing the pipes incorrectly in the cross sections. Whenever there is a crossing pipe running parallel with a structure, the pipe shows as a large ellipse instead of showing the pipe walls.
Some of the pipes are not running exactly parallel with the sample line, but they are pretty close. I know in the profile view you can change a setting to make a pipe show as a pipe end or as a regular pipe. Is there a setting for the cross sections as well? If not how do I get the pipes to show correctly?
View 5 Replies
View Related
Oct 30, 2012
This looks like an interesting tool
[URL]....
(No connection with Autodesk other than using the products in the real world)
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 2 Replies
View Related
Aug 20, 2013
Section editor shows the Existing Ground and the Assembly correctly. But "Create Multiple Views" Shows a blank Grid from -10 to 0..... Corridor rebuilt...
View 5 Replies
View Related
Dec 18, 2012
is there a way to turn off different levels of shading in the subassemblies that show up? when i orbit my road, i cant clearly see what is going on, and would like to turn off some shading. see image, i want to turn off where the arrows are pointing.
View 2 Replies
View Related
Jul 30, 2012
I have a corridor with two baselines, one on the south side of the road, and one on the north side. The south baseline appears correctly in the section view. It is an asphalt bike trail with a ditch to the left side. The north baseline was not appearing at all. The assembly was just a ditch with nothing else. I changed the north baseline to use the same assembly as the south to troubleshoot. The pavement comes in, but the ditch still does not appear.
I can see the ditch feature lines on my corridor (see attached), but they are not appearing in the section view.
View 1 Replies
View Related
Mar 28, 2013
have a good style to label cross sections at profile grade, top of curb, bottom of curb, grade breaks, and back of walks? Do I set a point or something in my assembly to use to label those points?
View 1 Replies
View Related
