AutoCAD Civil 3D :: Area Of TIN Volume Surface

Apr 4, 2012

I can see the area of a TIN surface no worries (under Surface Properties/Statistics/Extended), but want I want to get is surface area of a TIN volume surface where no "extended" option seems to be available to view the area information with this type of surface.

View 8 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Generate Volume Report For Bounded Volume Surface?

Oct 2, 2012

Is there a way to generate a volume report for a bounded volume surface?

View 3 Replies View Related

AutoCAD Civil 3D :: Sample Line Volume Report And Surface Volume Give Different Quantities

Jun 18, 2012

I'm working with TIN surfaces, doing cut/fill comparisons for a surface mine.

My volume surface statistics show a cut volume of 5167.22 cy and fill volume of 8456.18 cy.

The sample line group volume report show cumulative cut of 5527.67 cy and fill of 8465.56 cy.

What could be some causes of this disparity. All reference surfaces are built from points and use a non-destructive boundary.

View 2 Replies View Related

AutoCAD Civil 3D :: Cross Section Volume Vs Volume Surface

May 31, 2013

I've read a few threads on this way back but cannot locate them. I have two surfaces and create a volume surface and it reported the volume as 493 cy. I then ran some sample lines at 25 foot interval and the total volume is reported as 964 cy.

View 1 Replies View Related

AutoCAD Civil 3D :: Volume Bounded By Existing Surface And Design Surface

Dec 10, 2012

My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.

Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.

What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?

how do I shrink labels? Where is it in the settings ; the Align folder had been check.

View 2 Replies View Related

AutoCAD Civil 3D :: Exclude Area From Volume Calculations

Apr 4, 2013

I must monthly calculate quantities. So i have 3 surfaces, one is representing the original ground level and the other two the measurements on the end of the months. Between the measurements I calculated volume. But I want calculate the quantities what is inside of the original ground level, what is outside that I want to exclude from the calculations. There is a way how to crop that surfaces to match with the original ground level?

View 9 Replies View Related

AutoCAD Civil 3D :: Volume / Cut And Fill Area - Pavement Structure

Nov 13, 2012

Civil 3d project. My familiary with actual road construction is quite basic.

I'm at the stage where  good Civil 3d practices need to be employed when generating volumes. Attach are two files showing a road section with links and layers & also, the profile.

1. Like to turn off the links first of all and show labels instead.

2. How does the total depth of the gravel road (0.3' for gravel, 0.5' for aggregate base) factor in the profile view? What shown is the EG(in green) and FG,the top of the gravel road.

3. The cross section view: Three surfaces were used, the top of the gravel, the bottom of the base and the Existing ground, Is this correct?

4. Is there two sets of Volumes?  1. Cut and Fill areas,   2. Pavement structure: Volume of the gravel and volume of the aggregate base.

5.Refer to 4. So the Cut and Fill areas need to be done first, then the pavement structure, correct. ?

View 2 Replies View Related

AutoCAD Civil 3D :: Surface Volume And Display

Jun 3, 2013

I have a couple of questions regarding surface volumes/analysis in Civil 3D 2014.  First, there used to be a way to determine the volume between two surfaces without creating a volume surface.  The command is _AeccReportSurfaceVolume, but I can't find it on the ribbons in 2014 to save my life.  Do I need to create a new button myself?

Second, and more important, dealing with the elevation analysis in 2014, and noticed that the colors reset anytime that the volume surface is rebuilt?  It has always been annoying not to save a color scheme, but at least once you had set it up, the colors stayed as the surface changed.  Is there a new setting that I am missing, or is this just a glitch with 2014?

View 8 Replies View Related

AutoCAD Civil 3D :: Surface Volume Analysis

Jan 3, 2014

I have a large 200+ acre site that I have created a volume surface and analyzed it using the elevation banding with color to show different levels of cut and fill.  The owner has broken this area into 10 different irregular zones.  Is there a way to do the elevation banding of a volume surface and have it color the individual parcels.  They don't all have to be at once.  I can do each one at a time and PDF the drawing.

View 2 Replies View Related

AutoCAD Civil 3D :: Using A Surface For Volume Calculation?

Sep 25, 2012

I have run a volume between two surfaces, I need to further to break that new volume surface up to get volumes for each section. I know in microstation you can fence a volume surface and it will tell you the volume for that area. Is there a function in civil 3d that works like this. I know I can break it up manually and create new surfaces, I am looking for a time saving appoarch and trying to minimize file size.

View 2 Replies View Related

AutoCAD Civil 3D :: Zero Elevation For Volume Surface?

Sep 27, 2013

I'm getting a zero elevation for the surface I create when I compare surfaces to get volumes. What am I missing?

View 9 Replies View Related

AutoCAD Civil 3D :: TIN Volume Surface Shading?

Feb 10, 2012

I have a tin volume surface comprised of proposed and existing models for a large earthwork site. I would like a detailed cut fill diagram for presentation to project owner. The site involves cuts and fills up to 30' depths. I would like to be able to represent not only cuts and fills, but give a visual representation of the depth of cuts/fills (ie darker blues and reds in the deeper areas, lighter in the shallow areas). Is there a simple way to do this without setting up 100 different colors of blues and reds in the volume surface properties analysis tab? I have seen contractor software that performs this function rather easily.

View 9 Replies View Related

AutoCAD Civil 3D :: Tin Volume Surface And A Fixed Value

Oct 5, 2012

I'm have a tin volume surface with contours ranging between -0.240 and 0.000m. 

I have a need to display this surface as followed:

-0.220  - 0.000m as -0.220.

-0.240 (-) -0.220 as it is.

I've tried using contour intervals but nothing seemed to happen.

AutoCad 2011 & Civil3D 2011. Product Version 3.
EliteBook 8560w
Intel i7 CPU 2820QM @ 2.3GHz
8 GB RAM
NVIDIA Quadro 1000M
Windows 7 Enterprise 32 Bit

View 2 Replies View Related

AutoCAD Civil 3D :: Get Vertex From Volume Surface?

Nov 17, 2013

Civil 3D API has "TinSurfaceVertex" class and "GridSurfaceVertex" class.

I use those to get vertex:

foreach (GridSurfaceVertex vertice in GridSurface.Vertices) { Autodesk.AutoCAD.Geometry.Point3d punt = new Autodesk.AutoCAD.Geometry.Point3d(vertice.Location.X, vertice.Location.Y,

[Code]....
 
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit

View 2 Replies View Related

AutoCAD Civil 3D :: Surface Volume Is Wrong

Apr 22, 2012

1) when I try to find volume of a cube 1*1*1

c3d volume report is 0.03 c.meter why?

First I make surface1 and import the 4 point with elevation 0 sec. I make surface 2 and import 4 point with elevation 1 then itry to find volume of this cube and my result is 0.03 c.meter why this happen. 

2) if this above method is wrong give me step by step guide of surface and volume.

3) how to find volume at particular level.?

View 9 Replies View Related

AutoCAD Civil 3D :: Carriageway Surface Volume

Sep 10, 2013

I am trying to determine the volume of material (cut/fill) for a roadway surface in C3D 2013 using the volume dashboard.

I have created a fictional surface, basic profile and assembly so I can compare my calcs with C3D. After creating my surfaces and running the dashboard calcs, the program calculated the correct cut/fill volume. However looking at the surface in iso, I saw that additional surfaces were produced around zero elevation - refer to attached snapshot

In my actual model, I am well above zero elevation but these additional surfaces could cause problems on other projects.

View 2 Replies View Related

AutoCAD Civil 3D :: Editing Surface By Volume

Jun 12, 2013

I have a pumped storage project where I would like to know the water level if a volume of water is removed. Is there an easier way to do this? Currently I have my drawing set up with my base surface and various top water level surfaces. I have been creating volume surfaces for each TWL and populating a spreadhseet that indicates how volume and surface area differs with TWL. It would be incredibly handy to work this in reverse ie ask the volume surface to lose or gain a required volume of water and update the TWL accordingly.

View 3 Replies View Related

AutoCAD Civil 3D :: Surface And Volume Calculation

Nov 13, 2013

I attach picture 1 and 2.  

I need to create surface like this picture 2. I need crate surface by joining 1, 2, 3 like as picture 2 section, but when i crating surface its joining as picture.

This problem have been found . I created a tofo of the rock which rock is bend lower picture 2 section to calculate the volume i need the surface create like this. 

View 2 Replies View Related

AutoCAD Civil 3D :: Volume Surface Width Points

Apr 18, 2013

What I have is a tin volume surface. I am asked to label the points with the thickness of the volume surface.So where there was survey data on the top layer I need to have the width of the surface at those same points.

Any commands that can make this possible?

View 2 Replies View Related

AutoCAD Civil 3D :: Export Surface Volume Tables?

Mar 7, 2012

I'm working in Civil3D 2011.  How to export the data from the surface volume tables to excel, or any other format outside of Civil3D?  

Or maybe a better question: how to create a stage storage table automatically within Civil3D?  The elevations table gives volumes per elevation class, but I'm trying to get cumulative volume stored below various elevations in my reservoir.

View 9 Replies View Related

AutoCAD Civil 3D :: Showing A Volume Surface In Color?

Apr 29, 2013

how to make a color rendering showing cut and fill on a volume surface. I keep reading bits and pieces of how to do it, but nothing explaining a step by step process. The terminology keeps referencing elevation ranges? I figured out how to create a volume surface, but now desire to print out a colored drawing showing the cut and fill areas.

View 2 Replies View Related

AutoCAD Civil 3D :: Cut Fill Labels On Volume Surface

Jun 17, 2009

I need write Cut and Fill Labels on Volume surface in each 10x10 meters. Civil 3D can write Spot Levels on grid, but I need write Cut
and Fill values in grid area. Using Surface >Utilities>Bounded volumes I can get the values on selected closed polygon, but write to all is very long work. How to do write Cut and Fill labels on grid.

View 7 Replies View Related

AutoCAD Civil 3D :: Slicing Volume Of Surface At 1m Intervals

Nov 11, 2013

We design a lot of Waste storage facilities, mainly above ground level. I need to generate stage storage volumes at one metre intervals. Is there a way to automate this?

View 6 Replies View Related

AutoCAD Civil 3D :: Surface Volume - Can It Be Broken Down In Different Groups

Jun 18, 2012

can i divide them in 3 different areas that when i add their individual volume would give the same total volume if you calculate the entire surface?

View 5 Replies View Related

AutoCAD Civil 3D :: Possible To Create A Specific Contour In Volume Surface

Mar 2, 2012

I created surfaces in Civil 3d 2011 for existing and proposed and I did a surface volume between them. Is it possible to create a specific contour in the volume surface that represents the fill volume elevation (daylight line I think)? My proposed surface is a flood water elevation and I need to define the boundary at that elevation.

View 3 Replies View Related

AutoCAD Civil 3D :: Project Object To Surface / Volume Calcs

Jul 30, 2013

see attachment (object viewer capture). The top surface is my OG, the bottom surface is the bottom of excavation for a building. I want to project the perimeter of the building footprint up to the OG surface at a 1:5 slope. I remember in LDD the perimeter of a building, berm, dam, ditch...could be projected to the OG with specific slopes and then you could create a surface with the projected lines and do a volume calc. between the two. What is the procedure to do this in AutoCAD Civil 3D 2012?

View 5 Replies View Related

AutoCAD Civil 3D :: Surface With Specific Slope - Calculate Cut And Fill Volume

May 25, 2013

I use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.

I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.

View 9 Replies View Related

AutoCAD Civil 3D :: Calculate Volume With Both Sides Of Uneven Rock Surface In Excavation Pit

Nov 11, 2013

At my job site, they is about 20meter height of uneven rock surface in the excavation pit.

To calculate the volume ,I need to include this uneven rock surface wall.

For doing so,The sharp edge will displays in the cross section.

Because the uneven surface, I cannot create the surface with normal step.The TIn line will joins horizontally,not in vertical direction as is intended.

AutoCAD Civil3D 2014
Inter(R)Core(TM) i7-3770 cpu@3.40GHZ
RAM 8.00GB
64-Bit window7
QuadroK6000

View 2 Replies View Related

AutoCAD Civil 3D :: Create Volume Surface To Show Elevation Banding With Cut And Fill Ranges

Nov 12, 2013

I am working on a large park project.  I have a proposed and existing surface.  I have created a volume surface to show elevation banding with cut and fill ranges.  I need to create a drawing for someone who doesn't have civil 3d showing all the "cut" areas.  They really want a boundary of hatch.  What is the best way to do this after I change my analysis to -30 feet cut to 0 feet cut.

View 9 Replies View Related

AutoCAD Civil 3D :: Bounded Surface Area

Nov 24, 2013

I am trying to get C3D to report the surface area for a bounded area with no success.  I am aware of the Bounded Volume feature, which BTW appears to be retired in the 2014 release (AECCCFDBADDBOUNDEDVOLUME fails to produce any results). Obviously there have been some major changes.

What I want to do is retrieve a report for a defined section of a surface, regardless, of what type of surface it is.  I see this as simple as deriving the 3D areas of the trinangles within a bounds of a TIN. 

View 4 Replies View Related

AutoCAD Civil 3D :: Surface Depth Area

Nov 15, 2013

For a surface: I would like to a boundary above a inlet point that is 3" deep.

I would like something like catchment area but the ability to specify a depth distance. Or specify a depth in the water shed analysis in the surface properties.

The only way I know to do what I want is user defined contours for each elevation. Is there a better way to do get a specific shed area for a depth?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved