AutoCAD Inventor :: Draw Sheet-metal Elbow With (t) Junction

Sep 5, 2013

How to draw this junction on the Shet metal Elbow that i have create, i am sending what i have made so far and the 2d of what i need. My version of the Inventor is 2013.

View 4 Replies


ADVERTISEMENT

AutoCAD Inventor :: Unable To Unfold Sheet Metal Elbow

Oct 6, 2011

I'm looking to unfold the attached sheet metal elbow and am unable to do so.  After modeling the part I was also unable to rip an opening to split the part.  I opted to cut an opening with a profile, but I am still unable to unfold the part.  The probelm is likely obvious and I believe it is because I used part splits to create the different sections.

View 2 Replies View Related

AutoCAD Inventor :: How To Flatten Elbow Like Sheet Metal Development

Oct 30, 2012

I have an elbow with a slit on the other side and would like to use Flatten feature in sheet metal. How do I do it? I tried but an error pops-up, what does it mean.

I have attach the file.

View 9 Replies View Related

AutoCAD Inventor :: How To Draw With Sheet Metal Rules Centric Cone

Sep 30, 2011

How to draw with sheet metal rules centric cone? Ive spent hours on it and nothing, it always end up on ASM failure, or ceates the only one half( when sliced on asymetric way). This need to go in two halfs.

Ive tried:

two circles 1300 and 300, top circle centre moved from Y by 127mm on X axis.

contour roll will revolve on axis between circle centre points, than extrude something with cut and it is but the shape is an oval not circle.

Ive used loft command and slice command but only one side picke will work with flat pattern.

View 9 Replies View Related

AutoCAD Inventor :: Generating An Elbow On Metal Part Drawing?

Oct 17, 2012

how to create the elbow part of a metal type  ( actually a  J-shape Bolt  Threaded material)  .

I had finished  the  straight part  by  simply revolving my required profile. then i was to  draw the  elbow part but "sweep" doesnt  work  out

View 4 Replies View Related

AutoCAD Inventor :: How To Draw Segment Elbow 90 Degrees And Create Flat Pattern

Jan 16, 2013

I would like to know how to draw segment elbow 90 degrees ( segments are not equal ) and create Flat Pattern for each of the segments - using sheetmetal in Autodesk Inventor?

View 9 Replies View Related

AutoCAD Inventor :: Sheet Metal From Flat Sheet To Rolled Part?

Sep 12, 2013

A collegue asked me about this as he has been given a part to model and the details are for the flat sheet not the finished model. Is this possible in 'sheet metal'? I had a quick play but couldn't work it out. Im used to creating the finished part and 'un-folding' to get the flat pattern.Detail supplied below.

View 4 Replies View Related

AutoCAD Inventor :: How To Cut Sheet Metal

Jul 14, 2012

I just what to cut a sheet metal,

and I don't know how (see in Capture.JPG where i what to cut, and test.iam what I what to cut).

Where is the icon "project the geometry" ?

View 6 Replies View Related

AutoCAD Inventor :: Sheet Metal Elliptical

Jan 6, 2012

I need a flat pattern for this part but it seems impossible. STEP 2 illustrate the desirable result.

View 7 Replies View Related

AutoCAD Inventor :: Sheet Metal Imprint

Aug 21, 2013

Working with sheet metal and laying out a pattern for the cnc and was wondering if there is a way to imprint an extrusion onto the surface instead of cutting it. Mainly this will be used for a marking tool so the line type or layer would need to be different.

View 5 Replies View Related

AutoCAD Inventor :: Sheet Metal Bin - Add Flange

Aug 8, 2013

I am working on a bin type unit, and am having trouble creating a flange, I am creating the bin in the final product stage, then I will separate into manufacturer components. I am having trouble adding this flange around the top 4 edges of the bin. I need the four corners to meet on a miter 45. I will then rip down each seam and have 4 separate panels.

Is this a bad workflow? Is there a better route? I attached the part in Inventor 2013 format,

View 8 Replies View Related

AutoCAD Inventor :: Unfolding Sheet Metal

Dec 18, 2013

Attached are two sheet metal parts that we need to unfold and make them flat for a drawing. We cannot seem to capture the reference A or reference B planes asked for by the unfold command.

View 3 Replies View Related

AutoCAD Inventor :: Perforation In Sheet Metal

Jan 27, 2012

Is there a way to get the appearance of perforation on a sheet metal tube without having to create each and every hole?  Looking for an appearance to drag onto the surface. Kind of like when you make a part look like it is made of brick.  It being just an image on the model surface.

View 9 Replies View Related

AutoCAD Inventor :: How To Model ACM Sheet Metal

Oct 20, 2011

Very thin gauge aluminum sheets with a composite sandwiched between them.

The challenge is, the panels are relatively thick, 3mm or 4mm, but a router is used on the fold lines before bending to cut through all but the outer aluminum.  This makes for a very tight bend radius.

So, thick 3 layer material, tight bend with mitered corners.  Can Inventor's sheet metal tools handle this? 

View 5 Replies View Related

AutoCAD Inventor :: Sheet Metal Tools

Apr 17, 2013

Can this part be made with sheet metal tools...it will be made from aluminum. I attach the shape made with standard tools and the sheet metal attempt.......how do add the sides in sheet metal.

View 4 Replies View Related

AutoCAD Inventor :: Normal Cut In Sheet Metal

Sep 6, 2012

how incredible it is that Inventor still does not have a functional normal cut option for sheet metal like Solidworks and Solidedge have long had and I agree.  I realize that there are the standard workflows like using derive and thicken to get around this problem.  However, for those interested, there is a way to make a normal cut (for laser/cnc) directly in the sheet metal part in many cases.  It involves using a sketch to split a face and then using the resulting profile for a thicker/cut feature.  I'm always interested in any other methods out there for obtaining normal cuts in complex sheet metal (for a clean dxf export).  By the way, Autodesk, do you actually not have any plans of ever adding functionality in this area?

View 4 Replies View Related

AutoCAD Inventor :: Sheet Metal Tabs

Feb 3, 2012

what's the best way to make tabs on a rolled round ring.  I got it done using unfold/refold option but I can not get sheet metal flat. 

View 4 Replies View Related

AutoCAD Inventor :: Sheet Metal Extents Add-in?

Jul 3, 2012

I am using IV ultimate 2013

just found about this add-in:[URL]

But its not working for me:

I ran the installer, created a sheet metal part and hit rebuild all, it did not create any proeprties, also tried to manually create the properteis then hit rebuild, no go.

I also did a search on my hardrive for the ApplicationPlugins, and placed the sheet metal folder in all of them(there were 3) tried again noto.

The add-in also does not appear in the add-in manager.

Or is there different what to get the flat pattern dimensions in 2013

View 9 Replies View Related

AutoCAD Inventor :: Cannot Convert To Sheet Metal

Dec 7, 2012

I have just modelled a part with some faces and tried to convert to sheet metal to have inventor make the bends between the faces. However when trying to convert to sheet metal i get the following error message (Autodesk Inventor Professional Tip) - "This model cannot be converted to Sheet Metal because it contains features that have created multiple bodies. In order to convert to Sheet Metal these features must first be removed."

As the picture show the part only has 1 solid. Even when deleting all features except the "base" face I get the same error message or Tip as Inventor calls it.

View 5 Replies View Related

AutoCAD Inventor :: Sheet Metal - Cut Across Bend

Dec 20, 2012

I have a sheet metal door with a little bracket that gets welded to the inside lip through a cut-out in the face of the door. (see assembly)

I can't get the cut-out to line up flush with the inside lip of the door, as that is where the brackets gets welded to. the current aseembly is set-up the way I want, but I can't get a flat pattern on the door, becasue of the cut going across the bend.

I have checked off the "cut across bend" in the cut dialogue box, but this leaves a small (~1/32) lip in the cut-out and runs interference in the placement of the bracket. 

Inventor Pro Suite 2013
Sean Farr
Product Designer at TESInc.ca
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49

View 2 Replies View Related

AutoCAD Inventor :: Create A Sheet Metal Jog?

Oct 5, 2007

How can I create a sheet metal jog? Like the attached. I used a contor flange to creat this one, but I have to add a jog to an existing part and don't want to have to totally redraw it just to get the jog. I'm hoping you can add it like you can a flange.

View 9 Replies View Related

AutoCAD Inventor :: Slice Sheet Metal

Nov 13, 2011

I was designing a part which consisted in a circular sheet metal part with a hole in the center, and a bent rectangular radii-oriented section. The second feature is the one I want to give focus in this thread.

Take a circular sheet metal with a diameter of 30 mm and a thickness of 1 mm. Now, to achieve the bent section one would perform - in a workshop or any other equivalent - two parallel slices of about 5 mm in length with a distance from each other of 4 mm. The slice would start in the circumference and end somewhere nearer to the center of the disc, but not parallel to a radius (since its parallel to another slice 4 mm apart as said before). After the slicing was done, one would bend the section between the slices 90 degrees to any of the sides.

Now, in Inventor I couldn't find a way to do this. I couldn't just slice a line through the disc. I worked it around by cutting rectangles of 0.2 mm in width and with the length of the desired slices, and then using the folding command to bend it 90 degrees. Is it possible to perform this so called slices?

View 2 Replies View Related

AutoCAD Inventor :: Cuts In Sheet Metal Part

Sep 3, 2013

I made a part in sheet metal and used the Cut tool for cut-outs...i tried by using flatten Patern,draw sketch but this did not cut part...is there a more better way of making these cuts?

INV 2013

View 2 Replies View Related

AutoCAD Inventor :: Interlocking Joints In Sheet Metal

Apr 30, 2013

I have been trying to work out how to make interlocking joints in sheet metal parts. The attached screen shot is the only way I have found to do it in Inventor, but it is a cheat. One of the flanges is a 85˚ bend because if it were 90˚ it would give an error "Flange Body intersects with existing body or self intersects."

View 4 Replies View Related

AutoCAD Inventor :: Sheet Metal Rule In Drawing

May 7, 2012

I have setup all our Sheet Metal Rules to be all of our stocked in house sheet metals.  The sheet metal rules are named like:

ALUM 5052 H32 1/2" (Part Number)
ST STEEL T304 3/8" (Part Number)
STEEL 44W 1/8" (Part Number)
etc.

And each rule has the proper thickness, material, and some standardized bend radius's.  I've done this to introduce more uniformity in our designs, and to also allow the designer to put as much information into the model as possible, so that if someone else does the drawings, there is no question as to which material is used.

I now want to bring in the Sheet Metal Rule name into the drawing automatically.  I can't seem to find a way to reference the Sheet Metal Rule directly from the drawing.  What I need to do is pick a standard field in the i Properties (I used Stock Number), and put in =<Sheet Metal Rule> so that now the Stock Number references the Sheet Metal Rule, and then in the drawing I can just reference the Stock Number, and it will come in.

I don't like having to use the Stock Number as a middle man though, as none of our existing models are setup like this.  Is it possible to reference Sheet Metal Rule in the drawing without having to use another field as a placeholder for the information?  

View 7 Replies View Related

AutoCAD Inventor :: Flanged Sheet Metal Parts

Aug 2, 2012

I recently had an issue in adding flanges to a sheet metal part. The thread for that can be seen here:

[URL].......

The problem I am having now is with the size of the part. I need the linear distance from the bottom edge of a flange to match the inner diameter of my part. As you can see, this is not the case as it stands right now.

View 5 Replies View Related

AutoCAD Inventor :: Find Sheet Metal Thickness?

Oct 24, 2012

I am looking for a solid way of finding the Thickness parameter of a sheet metal part. I have tried two ways so far:

1. oCompDef.Parameters.Item(Thickness)

This works but if Inventor is installed with a different language pack like German for instance then it fails

2. oCompDef.Parameters.Item(1).Value

This also works but if the user started the part with a normal part template and then converts the part to a sheet metal part down the line, then this method fails.

View 1 Replies View Related

AutoCAD Inventor :: Automated Centerlines In Sheet Metal

Sep 11, 2013

Is there a reason a sheet metal "cut" isn't an option for the automated centerlines tool? Am I overlooking something? When I make holes in sheet metal parts, I draw the circle then "cut" it into the sheet metal. For some reason I can't find how to give those automatic centerlines on drawings.

View 6 Replies View Related

AutoCAD Inventor :: Sheet Metal - Angled Tray

Jan 20, 2012

I am trying to make an angled tray in sheet metal by am having some trouble getting it to work out.  I was unable to find an example of this type anywhere.  I tried doing it as a sheet metal part first then gave up, created a standard part and shelled it.  My problem is ripping the corners.

View 8 Replies View Related

AutoCAD Inventor :: Cannot Convert To Sheet Metal Part

Sep 16, 2013

For whatever reason this part was not modeled as a sheet metal part from the beginning, but now we would like to convert it to one.  But when the "Convert to Sheet Metal" button is pressed, an error message pops up saying "This model cannot be converted to Sheet Metal because it contains features that have created multiple bodies.  In order to convert to Sheet Metal these features must first be removed".  The only way I can get this message to go away is to delete all the features.  This part is used in a few weldments, so I'd rather not have to redraw it, but I'm at a loss as to why it can't be converted.

Using Inventor Professional 2014.

View 9 Replies View Related

AutoCAD Inventor :: Sheet Metal Gauge In Drawing?

Sep 20, 2012

I have created a bunch of sheet metal rules for my different gauge thicknesses. Is there a way I can propogate the gauge information to my drawing so that if I were to change the gauge, that info would also update on my drawing sheet? The only thing I can get to work currently is to pull in the material used, but that doesn't include the gauge.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved