All of a sudden I got this window when starting AutoCAD:"AutoCAD Application has Stopped working..A problem caused the program to stop working correctly.Windows will close the program and notify you if a solution is available."
I'm using v2013 on a desktop with Windows 8..I have been using the program since I got this new system in November without a hitch On sunday I had a nasty virus -Today I had to uninstalled AutoCAD and re-installed it and it worked good.After I closed it and went to open the application again I got the MESSAGE again
Let me know the solution for Getting "AutoCAD LT has Stopped working" while attempt to print in HP Laserjet M1536 dnf MFP Printer. I have tried the following steps but still i am getting the same Error.
1.Graphics Driver has been updated.
2.Printer Driver has been completely removed and reinstalled.
3.New configuration for this printer has been added.
4. AutoCAD LT 2013 Service Pack 1.1 has been installed.
System configuration: Win 7 -64 bit,4 GB ram, Intel-i3 2120 processor, Intel(R) HD Graphics.
A while ago I found out you can deselect something from your current selection set by holding down the shift key and clicking on it. This was a pretty useful tool...but then it randomly stopped working today for me.
i was using autocad 2013 without any trouble, i used break at point two times, after that i modified some layers and i think that nothing else, and the command break at point stopped working, when i press it it automatically uses the command break. what is going on?
I'm using GIMP in my own language so the tools names translation might not be 100% accurate.
Been using GIMP (2.8 and just switched to the latest one) for a while now, it's been nearly a year on this PC (Windows 7 64 bit, relatively recent hardware, 8 Gb of RAM, etc.) and it's worked smoothly up until a couple of days ago when it stopped working as intended all of a sudden for some reason.
Whether I use my Wacom tablet or the mouse none of the tools that normally allow you to draw (pencil, brush, airbrush, etc.) work anymore (cropping, distorting the image and the likes work fine though), doesn't matter if it's a brand new document or an old file.
The funny thing is that when I go to the "Edit" menu it'll allow me to rollback and undo whatever I did with the aforementioned tools, even though there's no trace of it on the empty canvas itself.
I tried to uninstall and install the software back but it didn't do the trick.This is really irking me as I'm working on an illustration that is due in a week and I basically had to stop working on it altogether because I haven't been able to get rid of this problem (also I can't seem to find anything about this specific issue on the net).
I am operating 3D Civil with Windows 7, 64-bit system.
Most of the time when I close a drawing, particularly when I have two or more drawings open, the program closes down with the following message "Autocad Application has stopped working - Windows is collecting more information about the problem"
All of a sudden, my action macros aren't working. I'm getting "Unknown command" errors. I've checked my options, everything's pointing to the right folder, and the macro files are in the right folder. Why would I be getting this error?
I was working normally in a drawing (ACAD 2012, 32b) file when, without any apparent reason, I tried to delete something and it didn't work. The way I work is that I select first and then press the "delete" key.
Now, when I do this, absolutely nothing happens. The objects remain selected. While trying to figure out what was happening, I discovered further disruptions. For example, when I select and object and then right-click, instead of showing me the edit shortcut menu, it repeats the last command. I know what you are thinking, but I already verified the right-click customizations and it is correctly set to "shortcut menu" in the "edit mode".
Finally, when I double click on a text, it won't edit as expected; again, nothing happens. Ane yes, in "Options/Windows standard behaviour" the "Double click editing" options is selected.
All the above has it's way around: the "erase" command works, the "ddedit" text works, etc. But it slows me down horribly.
I'm currently using Civil 3D 2012, and all of a sudden CTRL+Z has stopped working as UNDO. It does nothing. I've found this issue in lots of other outdated forum posts, but none seem to relate to Civil 3D 2012. I went into CUI to see if the shortcut was somehow changed, but the UNDO command still points to CTRL+Z as its shortcut.
I recently did a repair on my C3d 2012 (whcih didn't fix the problem, but I found out what that was and sorted it another way.)
I now find that all express tools commands give me the command unknown error.
I have checked in the cui and the Express tools ARE loaded. I tried unloading and reloading acermain.cuix without success.
I tried adding features from the control panel, but express tools do not show in the list.
I checked the text window after I first opened C3d and it definitely lists that it has loaded express tools yet they do not work.
I tried typing expressmenu in the command line, but it says command unknown.
edit - I tried resetting acetmain.cuix and got the following error:
Unhandled exception has occurred in a component in your application. If yu click continue the application will ignore this error and attempt to continue.
Unable to cast object of type 'Autodesk Autocad Customization CUIUnresolvedCUIFileNode to type Autodesk Autocad Customization CUIPartialCUIFilenode'
I have a rule in iLogic that I was testing as "Straight VB.Net" on various assemblies. It was working alright, but I was making some minor tweaks to eliminate errors. Now, all of a sudden, it is unresponsive. Completely. No errors, no "busy" symbol over my pointer, just nothing. I put in the line MsgBox("Begin") as the first line of the program to see if it was even getting into it, and still there is no response. I run the rule, and absolutely nothing happens. I tried writing it in iLogic instead, and that does make something happen. what might cause the VB.Net element of iLogic to stop working, and hopefully how to correct the problem as well?
One minute it was working, and then suddenly I can not use the "down arrow" to access the additional dynamic input options. It must be a profile setting, because it works in all my other profiles.
So the other day I set up an external rule and created an event trigger to run the rule on save. It worked great ... for a couple days, and then it just stopped working yesterday. I can still run the rule manually and it works fine, but it doesn't seem to run automatically anymore on file save. Yes, iLogic is set to Loaded / Automati in the add-ins panel.
(on the iLogic rule attachment, remove .TXT from the end. I had to add that due to the board's rules about file types.)
Product Design Suite Ultimate 2013, 2014 Autodesk Inventor 2013
I tried to open the Storm and Sanitary Sewer analysis program and got an error message. The error message asked me to send a report but the report was rejected.
My Photoshop CS4 and CS5 shows "Photoshop has stopped working" . Whereas I have Windows 7 64bit, 6GB RAM, 512MB Graphics Card.
Earlier I worked in this version. But after formating my conputer I could not do anything with only in Photoshop. First I installed Photoshop CS4 it was failed to work then install Photoshop CS5..It also failed to work.
I updated Photoshop CC about 7 days ago. Before that it worked fine, since then I have been using Photoshop CS6 for some work (CC left it there when it installed) but yesterday I wanted to go to Photoshop CC from Lightroom 5.2 and Photoshop CC hung. Rebooted computer and tried to open Photoshop CC but it crashes on initialization.
As interim measure I installed PS CS6 as an optional external editor in Lightroom, but I would like to use Photoshop CC again one day!
Yesterday, I tried to start up Photoshop, but it got halfway through initializing and stopped, flashing a message: "Adobe Photoshop CS5.1 has stopped working." I shut down the computer and tried again, but it repeated three or four times.
So I uninstalled the program. Upon reinstallation, installation failed and the computer said: "Your installation encountered errors. Please try restarting your system and installing again. Exit Code: 20."
I have been using my program since June without issue. Suddenly it stopped working. I can open the program but it will not create a new file or open an existing file. If I "open with" from windows explorer it won't open either. I have uninstalled and reinstalled the program and I'm still not having any luck.
I get an error message from windows vista premiumm home.
It just says: Adobe Photoshop CS3 has stopped working correctly. Windows will close the program and notify you if a solution is available. The only option is a box that says "close program". Once you close it everything goes away. It doesn't even give you a hint of what the problem could be. I installed creative suite 3 web premium on this brand new computer about 2 weeks ago. This is a first time install of this software, but when I called Adobe they said they don't offer free installation help anymore on cs3 because cs4 is out now. Anyone have a clue what I should do? I can't just uninstall photoshop, if I try it wants to uninstall all 8 programs.